Talos Security BX1080P HD-SDI - Manual

User Manual
HD-SDI Camera
6 Trouble Shooting
1 Main Features
2 Important Safety Instructions
. Please read this user manual carefully before using the camera, and keep it well for future
reference.
. Please transport, use and place the camera in allowable temperature and humidity range.
. Please avoid heavy stress or violent vibration.
. To reduce the risk of fire or electrical shock, do not expose this product near the heat,
water or moisture.
. Please disconnect any cables during an electrical storm or the camera will not be used for
an extended period of time.
. Must observe all electrical safety standards; make sure the power supply voltage is
correct before using the camera.
. Do not aim the camera lens at the strong light, otherwise it will cause fatal damage to
photosensitive element.
. Do not install the camera near the outlet of air conditioners, otherwise lens will become
fuzzy due to condensation.
. If cleaning is necessary, use dedicated lens paper or a clean soft cloth with a bit of neutral
detergent diluted with water and wipe it gently.
. If the product does not work properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the camera yourself.
(07)HDR (High Dynamic Range):Turn on this function to balance the contrast between
light and dark areas within an image. User can see highlight areas (under strong
light)and low-light areas (shadows, backlighting, etc) simultaneously, otherwise
highlight areas display white and dark areas display black.
(14)Restore Factory Setting:Select this option and press L or R key to restore the factory
settings, and then save it.
Note: If user changed the settings and not saved, exiting menu can save the settings
temporarily, but not memorize the current settings when power lost, and will
restore to the previously saved settings.
HD-SDI Camera
Power Port
Power Supply
HD-SDI Port HD-SDI-HDMI
Converter or
HD DVR
Monitor
5 Connection Guide
Item Fault Solution
1
2
3
4
5
The image on the
screen is dim
Dysfunction and cannot
be adjusted
Please restore the factory settings.
Camera does not work
properly, or overheat,
smells bad or smoking
Please cut off the power immediately, check whether the camera is correctly
connected to appropriate power, then maintenance overhaul by professionals.
Power Supply
Image Resolution
Sensor Specifications
Pixel Size
Color System
Video Output
Video Output Interface
Shooting Speed
Min. illumination
OSD
Scene Mode
Infrared Switch
HDR
Analog Gain
2D DNR
Automatic Exposure Response Speed
AWB
CCM
DPC
Brightness/Contrast/Saturation/Hue
Self Adaption
Auto Iris
Transmission Distance (Non-Relay)
Power Consumption
Working Environment
Power adapter: 12V(min 0.5A)
1080P(1920×1080)30Hz/25Hz
1/2.5 inch
2.2um x 2.2um
Ycbcr 16bit
HD-SDI (SMPTE274M standard)
BNC
30fps/25fps
0.1LUX (single-frame and color mode)
Support multiple languages (up to 30 and flexible customize)
General/Highlight
Auto/Color/Gray
ON/Off
ON/Off
ON/Off
8 frames
Auto/Mode 1/Mode 2/Mode 3/Off
ON/Off
ON/Off
0~255 adjustable
ON/Off
Selectable
Min 300m (the quality of coaxial cable is optional)
Max 2W (with 12V power supply, IR off)
℃ ℃ ≤90% Temperature: - 10 ~ + 50 Humidity:
3 Appearance and Parts Description
User manual is only for reference; please make the actual product as standard.
(2)Power input: connect to DC12V power adapter.
Note: The SDI menu control line of camera contains SDI video cable
and power cord.
(3)OSD control keys.
4 Menu Setup
User can use OSD control keys on SDI menu control line to operate menu; as
shown below:
UP
R L
DOWN
Key
UP/DOWN
L/R
Meaning
Move up/down
Choose to left/right or confirm
Menu key:Open and close menu
Note:Push the Menu key to these four directions to complete the direction key
functions.
Press the Menu key to pop-up menu on the screen, as shown below. Use the UP/DOWN
key to move up/down in the menu. The selected option displays in a black background.
Use the L/R key to choose the parameters for current option, or confirm operation when
there is no parameter to choose. Press the Menu key again to exit menu.
MENU
Language
Video Resolution
Scene Mode
Infrared Switch
CCM
AWB
Saturation
Hue
Self Adaption
Save
Restore Factory Setting
[English]
[1080P/30]
[Highlight]
[Auto]
[Off]
[Auto]
[128]
[20]
[ON]
HDR [ON]
[ON]
[ON]
Analog Gain
Brightness
Contrast
[ON]
[128]
[128]
(01)Language:Select the menu language; support more than 30 languages and
flexible customize.
(02)Video Resolution:Full HD video output: 1920 × 1080P 30/25fps. User can
select 1080P/30 or 1080P/25 according to actual demand.
(03)Scene Mode:Select the video screen brightness, there are two picture
effects: General and Highlight.
(04)Infrared Switch:Switch between day and night in three seconds.
[Auto]The camera can change its parameters automatically according to the
external environment. It switches to color mode in the normal environment
(such as during the day) in order to get the ideal color; switches to gray mode
when the ambient illumination is low (such as at night) in order to get the
image clearly.
[Color]Always display color pictures.
[Gray]Always display gray pictures.
(05)CCM (Color Correction Matrix):Turn on this function to make the picture more vivid.
(06)AWB (Automatic White Balance):It may cause the sensor color cast under special
environment. Set AWB mode to adjust the color of screen and make the picture
closer to actual results.
Five modes: Auto, Mode1, Mode2, Mode3, Off.
(13)Save:Select this option and press L or R key to save the current setup. The camera
can memorize the saved settings when power lost.
Note:After “Self Adaption” is turned on, “scene mode”, “HDR” and “2D DNR” can’t
be supported by manual settings; when “Self Adaption” is closed, these three
menu options can be supported by manual settings.
(09)2D DNR:Turn on this function to reduce the background noise in low-light
environment.
(10)Analog Gain:When the exposure is not enough under special environment, turn on
this function to amplify signal and enhance brightness.
(11)Brightness / Contrast / Saturation / Hue:Set these options to meet the various
requirements of screen brightness, color vividness etc. Press L or R key to adjust
the brightness/contrast/saturation/hue, range from 0 to 255. The default value
is 128/128/128/20.
(12)Self Adaption:This function can greatly enhance the self-adaptability for different
environments, and facilitate user to set the menu.
[On]The camera will change some of the options in OSD menu automatically based
on current scene. For example, it will open the "highlight" mode when the scene
lighting is dim; it will open the "2D DNR" when the video noise is serious; it will open
the "HDR" when the scene contrast is larger, and so forth.
[Off]Turn off the intelligent self adaption.
(08)DPC(Dead Pixel Correction):Turn on this function to repair the dead pixel.
7 Specification
. 2 mega-pixel HD CCTV video coaxial cable to achieve real-time 1080P HD image output
. Full HD video output: 1920 × 1080 30fps, 25fps optional
. Standard HD-SDI high definition digital interface
. Uncompressed HD video raw data real-time output
. Support infrared switch
. Day and night, with IR Cut
. Flexible OSD
. Support automatic and manual lens
. Low power consumption
. CCM, HDR, DPC, 2DNR, AGC, AWB, etc
.
1
2
3
1/2
(1)HD-SDI high-definition digital video signal output: connect to HD DVR or HD-SDI to
HDMI converter to display.
1.Check that the power cord and line connection between the camera and
monitor are properly connected.
2.Is the camera framing the sun or the bright light source?
3.HD-SDI video may not appear to be normal if distance exceeds the maximum
transferrable distance.
4.When a BNC cable adaptor is used to combine two or more BNC cables for the
distributed HD-SDI video transfer, make sure the impedance of the adaptor is
75Ω. Otherwise, it may shorter transfer distance or broken video transfer.
5.When the camera’s HD-SDI BNC output is directly connected to the monitor’s
BNC terminal or DVR: Make sure the monitor or DVR supports HD-SDI signal
input.
6.HD-SDI output is converted into other format such as HDMI by using video
converter: Make sure the converter’s HD-SDI input format supports the
product’s output video format.
The screen flickers
or no image
The picture is
blurred
1.Check lens for dirt; cleaning method see Cautions 9.
2.Check whether the focal length and settings are correct.
1.Is lens stained with dirt? Clean your lens with soft, clean cloth.
2.Set the monitor to the proper condition.
3.If the camera is exposed to very strong light, change the camera position.
IP Grade IP65 (according to different products)
DPC
2D DNR