S&S Cycle T111 Engine Assembly - Manual (Page 16)

16
1. Bolt, stator 10-24 x1” SHC - 4 required
(H-D#2720) (10 Pack) ....................................................50-0194
2. Seal, sprocket shaft (H-D#12068) ..............................31-4035
3. Bearing, Timken ® sprocket shaft (H-D#9028 )...........31-4013
4. Bolt, case 5 ⁄
16
” -24 x 2 3 ⁄
4
” HHC - 8 required
(5 Pack) .......................................................................50-0190
5. Washer, flat 5 ⁄
16
” x 11 ⁄
16
” x 1 ⁄
16
” - 8 required
(10 Pack) .....................................................................50-7069
6. Bolt center case 1 ⁄
4
” -28 x 6” HHC Grade 8
(5 Pack) .......................................................................50-0221
7. Washer, flat, 1 ⁄
4
” x .474” x .050” (10 Pack) ................50-7076
8. Cylinder studs (H-D#16834-99) (8 Pack) ......................31-2340
9. Dowel, cylinder deck - 2 required
(H-D#16595-99) (10 Pack) ..............................................50-8179
10. Nut 1 ⁄
4
”-28 Grade 8 - 1 required (10 Pack) ...............50-5014
11. Bolt, cam plate 1 ⁄
4
” -20 x 1” SHC - 4 required
(10 Pack) .....................................................................50-0244
12. Bolt, cam plate 1 ⁄
4
” -20 x 1 1 ⁄
4
” SHC - 2 required
(10 Pack) .....................................................................50-0153
13. O-ring, cam plate - 9 required
(H-D#11301) (10 Pack) ..................................................50-8066
14. Dowel, cam plate - 2 required (H-D#16589-99) ........50-8148
15. Bearing, inner cam (H-D# 9198) .................................31-4080
16. Bearing, pinion shaft – Fits all S&S and OEM 2000-’02
(Balanced models only) & all OEM 2003-up
(H-D#24604-00 & #24604-00C) ........................................31-4085
17. Retaining ring, internal, spiraloc
(H-D#35114-02) (6 pack) ................................................50-1047
18. O-ring, oil pump 11 ⁄
16
” I.D. x 15 ⁄
16
” O.D. x 1 ⁄
8
” CS
(H-D#11293) .................................................................50-8039
19. Switch, oil pressure
Case with rear motor mount, 1948-’99 big twin
(H-D#26561-84) (Not shown) ..............................................31-2016
NOTE: Stock style use stock pressure switch.
20. Plug, magnetic drain ..............................................50-8335
21. Baffle Plate ..............................................................31-0119
22. Screw 10-24 x
3 ⁄
8
” panhead - 2 required
(10 Pack) .....................................................................50-0139
23. Dowel, case alignment - 2 required
(H-D#16574-99) (10 Pack) ..............................................50-8109
24. O-ring, case alignment, 9 ⁄
16
” I.D. x 11 ⁄
16
” O.D. x 1 ⁄
16
” CS
2 required, (H-D#26432-76A) (10 Pack) .......................50-8102
25. Piston oilers - (Kit of 2) (H-D#22371-99) ....................31-2026
26. Hardware kit, oil line plugs.....................................50-1081
27. Fitting, crankcase vent
1999-'00 (2 Pack) ......................................................106-1172
2001-'06 (2 Pack) ......................................................106-1171
28. Plate, oil line cover ................................................106-1184
29. BHSH CS
5 ⁄
16
-18 x 3 ⁄
4
" (10 Pack) ..................................106-1178
30. O-ring (10 Pack) .......................................................106-1183
These parts are for crankcases manufactured before 8-1-06:
31. Plug, sump
(H-D#765) .................................................50-8330
32. Oil conduit block......................................................31-2076
33. Washer, flat
1 ⁄
4
” chrome (12 Pack) ............................50-7013
34. Bolt, 1 ⁄
4
” -20 x 3 ⁄
4
” SHCS - 1 required (12 Pack) .........50-0144
35. Hose, oil, inlet/outlet ...............................................50-8157
36. Spring clips
(10 pack) .................................................50-8156
37. Oil line fittings, inlet/outlet - 2 required................50-8158
38. Oil line fitting- vent
(H-D# 25259-93A) ......................50-8146
Replacement Parts for S&S ® Crankcases for Harley-Davidson ® Twin Cam 88 ® Engines
All reference to H-D ® part numbers is for identification purposes only. We in no way are implying that any of S&S Cycle’s products are original
equipment parts or that they are equivalent to the corresponding H-D ® part number shown.
1
2
3
4
5
6
7
7
8
8
8
8
8
8
8
8
9
9
10
11
12
13
14
12
14
15
15
16
17
17
18
28 20
20
21
22
22
23
24
25
26
27
29
30
31
32
13
13
33 34
35
35
36
36
36
36
37
38
13
13