MTS Series 244 Actuators User Manual
Page 24
Actuator Dimensions
Description
Item
BASIC CYLINDER
1
FRONT END CAP
2
REAR END CAP
3
A (Cushion)
4
Stroke Length
5
C min.
6
B+ Stroke Length
7
-6 Drain
8
Rod Insert: “M” thread size, “N” deep
9
Structural
10
Load Frame
11
“D” holes, “E” thread size, “F” deep, equally spaced on a “G” diameter
12
4 holes, “H” thread size, “F” deep, equally spaced on an “L” diameter
13
8 holes, “H” thread size, “K” deep, spaced as shown on an “L” diameter
14
Each dimension shown in this figure is listed in the table that follows.
Actuator Dimensions (SI Metric)
Model
Item
244.51
244.41
244.31
244.23
244.22
244.21
244.20
244.12
244.11
Units
none
none
5.1
6.4
7.6
10.2
10.2
15.2
15.2
mm
A
342.6
311.6
256.5
233.7
233.7
246.4
246.4
238.3
238.3
mm
B
38.1
28.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
mm
C
4
8
8
8
8
8
8
8
2 or 4
2 or 4
holes
5
D
1 - 8
1 - 8
5/8 - 11
1/2 - 13
1/2 - 13
1/2 - 13
1/2 - 13
3/8 - 16
3/8 - 16
UNC
E
4
This area includes a fully retracted standard length piston rod.
5
Load unit actuators have four mounting holes; structural actuators have two mounting holes.
24 Series 244 Actuators Product Information
Introduction
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)