Metal Sales Pro-Panel II Manual - Manual (Page 6)

PPP-6 © Metal Sales Manufacturing Corporation/ Subject to change without notice/ Effective Date 9/11
800.406.7387 (Corporate Office) • www.metalsales.us.com
PRO-PANEL II ® s
eCTion
P
roPerTies and
l
oad
T
ables
Anti-Siphon Groove C
36" Coverage
3 1 /
8
" 2 3 /
4
"
9"
5 /
8
"
Optional
Profile
ALLOWABLE UNIFORM LOADS PSF
(3 or More Equal Spans)
2' 2.5' 3' 3.5' 4' 5' 2' 2.5' 3' 3.5' 4' 5'
SECTION PROPERTIES
Bottom in Compression
Width
(in.)
Yield
KSI
36" 80
36" 80
29
Ga.
26
Sxx
In 3 /ft
Ixx
In 4 /ft
Weight
PSF
0.71
0.87
Top in Compression
Sxx
In 3 /ft
Ixx
In 4 /ft
0.0067 0.0134 0.0047 0.0133 90 58 41 27 18 9 90 59 41 27 18 9
0.0090 0.0181 0.0063 0.0170 115 75 52 35 23 12 122 79 55 35 23 12
Inward
Load
Outward
Load
1. Theoretical section properties have been calculated per AISI 2001 "Specification for the Design of Cold-Formed Steel Structural Members.”
Ixx and Sxx are effective section properties for deflection and bending.
2. Allowable load is calculated in accordance with AISI 2001 specifications considering bending, shear, combined bending and shear and
deflection. Allowable load considers the worst case of 3 or 4 equal span conditions. Allowable load does not address web crippling or
fastener/support connection and panel weight is not considered.
3. Deflection consideration is limited by a maximum deflection ratio of L/180 of span.
4. Allowable loads do not include a 1/3 stress increase in uplift.
5. Diaphragm 306 plf average Ultimate Shear Strength using the above fastening pattern on 2x supports located 2' on center per ASTM E455-04
 Slope
 Substructure
 Coverage
 Length
 Fasteners
 Availability
GENERAL INFORMATION ATTACHMENT DETAIL
The minimum recommended slope for Pro-Panel II ® roof
panel is 3:12.
Pro-Panel II ® is designed to be utilized over open structural
framing, or a solid substrate. To avoid panel distortion, use
a properly aligned and uniform substructure.
Pro-Panel II ® panels are available in a 5 /
8
" rib height with a
coverage width of 36".
Minimum factory cut length is 5'-0". Maximum
recommended panel length is 45'-0". Longer panels
require additional consideration in packaging, shipping, and
erection. Please consult Metal Sales for recommendations.
The fastener selection guide should be consulted for
choosing the proper fastener for specific applications.
Quantity and type of fastener must meet necessary loading
and code requirements.
NOTE: All panels are subject to surface distortion due to
improperly applied fasteners. Overdriven fasteners will
cause stress and induce oil canning across the face of the
panel at or near the point of attachment.
Finishes: Acrylic Coated Galvalume ® or MS Colorfast45 ®
Gauges: 26 ga and 29 ga standard
FASTENING PATTERN
Anti-Siphon Groove
1 /
4
"-14 x 7 /
8
" Stitch Screw (1'-0" o.c.)
#9-15 Woodscrew
1 /
4
"-14 x 7 /
8
" Stitch Screw #9-15 Woodscrew
Optional
Profile