Lightforce 240 BLITZ REMOTE MOUNT DL - Manual

1. Ensure all electrical connectors are secure; loose connections will generate excessive heat, damage wiring and causing
electrical failure.
2. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping it with a dry rag will
scratch the lens, especially if the surface is dusty. NEVER clean the light with cleaning fluid or solvent.
3. DO NOT attempt to clean the inside of the light or touch the inside lens and reflector.
4. LIGHTFORCE lights are not designed to be used for long periods of time in a stationary position with minimal airflow, failure to
comply will void warranty. Contact LIGHTFORCE direct to discuss alternative options such as reducing globe wattage.
5. GLOBE REPLACEMENT: The Xenophot® globe gives approximately 10% greater efficiency than any other halogen globe of similar
voltage. A number of optional globe strengths are available upon request. For removal, simply:
a) Rotate the reflector housing anti-clockwise to disengage it.
b) Remove old globe by gripping firmly and pulling out in the long axis direction of the globe.
i) DO NOT TOUCH NEW GLOBE WITH FINGERS, use a tissue or plastic sleeve. Prior to inserting a new globe, scrape the
globe legs with an abrasive surface (sandpaper or knife edge) to ensure positive contact with the globe holder electrodes.
ii) Position the globe legs firmly into the fixed electrodes of the globe holder, applying a firm pressure towards the rear. AVOID
jerking or twisting movements. NOTE: Globe can only be moved to the left and right NOT up and down.
iii) Mere placement of the globe into the globe holder is often not sufficient to give a properly fine tuned beam. The operator
can overcome this by aligning the split line along the top of the rotation locking NIB and the split line on the end of the
handle with the centre of the globe filament. (see Fig.1)
v) All other globes should be seated against the globe holder with little or no air gap.
vi) Maximum globe wattage recommendation:
140 LANCE: 12V 75W
170 STRIKER: 12V 100W
240 BLITZ: 12V 100W
Note: USING GREATER WATTAGE WILL VOID WARRANTY
6. FOCUSING MECHANISM: The patented focus mechanism allows precise adjustment of the beam to various concentration patterns as
desired. Simply rotate the reflector and select the desired SPOT.
7. Ensure that during use the reflector surface is not wound too far forward past the globe holder or melting of the housing can occur and
will not be covered under warranty.
8. We recommend wiring remote mount driving lights with a minimum 10 amp wire.
9. Tools needed for installation are
• 17mm socket on ratchet x 2 or equivalent
• Torque wrench
10. Your HID light can be mounted with the bottom mount bracket fitted in either direction (i.e. rotated 180 degrees). If you find that
you need to mount your light lower then our ‘low mount’ bracket can be purchased (part number #MVDL). This can also be turned
180 degrees for a greater offset than the standard ‘high mount’.
11. Determine suitable mounting position and fit light into position.
12. Aim light (i.e. point straight ahead) then tighten both bolts as per recommended torque specifications (see specifications below).
13. Mounting fastener torque specifications are all M10 bolts - 70Nm (50lb-ft).
LIGHTFORCE AUSTRALIA PTY LTD • 28 Orsmond Street, Hindmarsh SA 5007 Australia • www.lightforce.com | email: [email protected]
Australia: Tel: 08 8440 0888 | Fax: 08 8346 0504 • Int’l: Tel: +618 8440 0888 | Fax: +618 8346 0504
All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd | © March 2013 • Data and specifications contained maybe subject to change without notice.
LIGHTFORCE AUSTRALIA Pty. Ltd., shall be not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modification, unauthorised or non standard replacement parts, accessories,
globes, batteries or voltage or the operation of the Product beyond its technical and environmental specifications.
INSTRUCTION DATA
PRODUCT: REMOTE MOUNT DL
VER: 1.0
DATE: MARCH 2013
Fig.2
Fig.1