Lenze EPM-H515 - Manual (Page 69)

Commissioning
Project transfer to the operating unit
Disconnecting from the PC
5
69 EDBPM-H515 DE/EN/FR 2.0
What to do
A
Switch on the PC and start the »HMI
Designer« planning tool.
B Switch on the supply voltage for the
operating unit. 0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
The device is being initialised.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
C After initialisation, select the system page.
For this purpose, touch the display at the
corners
top right and bottom left or
top left and bottom right .
The first corner to be touched must not
contain a selectable field.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE The system page appears.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
D Touch the ”TRAN PAGE” field.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
The transfer page appears.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
E Touch the field MSP.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
The operating unit is ready for data
reception of the PC.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
F Transfer the desired project from the »HMI
Designer« into the operating unit.
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
E HMI Designer - Getting started”
0
1
2
H515 TRANSFER PAGE
Touch screen BOOT check:
OK
Graphic controller BOOT check: OK
Graphic controller RAM check: OK
Main BOOT and RAM check: WAIT
3
SELECT: MSP ASP EXIT MemoCARD
Port : NET
Driver : CAN Lenze M
Ver : 1.12
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
“PROGRAMMING MODE” is displayed during the download.
G After download is completed, the operating unit is ready for operation and can exchange data
with the connected nodes by the system bus. The project is stored after disconnection from the
supply voltage.
5.2.3 Disconnecting from the PC
1. Switch off the PC.
2. Switch off the supply voltage for the operating unit.
3. Remove the EPZ-H110 download cable from the operating unit and the PC.
4. Switch on the supply voltage for the operating unit.
The operating unit is now ready for operation.