beautypg.com

Bunn DV User Manual

Page 14

background image

14

SERVICE (cont.)

Solenoid Valve (Late Models)

Location:
The solenoid valve is located inside the rear of the
dispenser on the right side near the bottom.
To test the solenoid valve, access will also be needed
to the electronic control board.

sound after approximately 5 seconds, as the coil
magnet attracts the plunger.

8. Disconnect the dispenser from the power source.
9. Reconnect the pink wire to terminal 5 of the elec-

tronic control board.

If the sound was heard as described and water will
not pass through the solenoid valve, there may be a
blockage in the water line before or after the solenoid
valve or the solenoid valve may require inspection for
wear and removal of waterborne particles.
If the sound was not heard as described, replace the
solenoid valve.

Removal and Replacement:
1. Remove all wires from the solenoid valve coil.
2. Turn-off the water supply to the dispenser.
3. Disconnect the water line from the solenoid valve.
4. Remove the two 8-32 slotted-head screws holding

the solenoid valve and mounting bracket to the back
panel.

5. Lift-out the solenoid valve.
6. Securely install the new solenoid valve to the back

panel.

7. Securely fasten the water line to the solenoid valve.
8. Reconnect the wires, FIG. 8.

Fi

ll w

at

er

tan

k bef

or

e tur

ning

-on

thermo

sta

t or

co

nnect

ing

ap

pli

anc

e

to p

ow

er sour

ce.

Do n

ot us

e ne

ar

combus

tib

les

.

Foll

ow

nat

ion

al/loc

al e

lec

tric

al c

odes

.

Elec

trically

gr

ou

nd

the c

ha

ssis

.

Us

e o

nly o

n a

pr

oper

ly pr

ot

ec

ted

cir

cuit

capa

ble

of

the

rat

ed

load.

FAILURE

TO

COMPL

Y R

ISKS

EQ

UI

PM

ENT

DA

MA

GE,

FIRE

, O

R

SH

OC

K

HA

ZAR

D

RE

AD

TH

E E

NTI

RE

OP

ER

ATIN

G

MA

NUAL

INCL

UD

ING THE

LIM

IT OF

WA

RR

ANTY

AN

D

LIA

BIL

ITY

BE

FOR

E BU

YIN

G

OR

US

ING

TH

IS

PRO

DU

CT

TH

IS A

PPLIA

NCE

IS

HEA

TE

D WHE

NEVE

R

CON

NE

CTE

D T

O A

PO

WE

R SOU

RC

E

008

31.0

000

A 5

/88

© 19

88

BUN

N-O

-M

ATIC

CO

RPO

RAT

ION

WARNI

NG

!

Test Procedure:
1. Disconnect the dispenser from the power source

and turn-off the water supply to the dispenser.

2. Remove the pink wire from terminal 5 of the elec-

tronic control board.

3. Check the voltage across the solenoid valve coil

terminals with a voltmeter. Connect the dispenser
to the power source. The indication must be:

a.) 100 to 120 volts ac for 100 to 120 volt models
or

b.) 200 to 240 volts ac for 200 to 240 volt models

or

c.) 230 volts ac for 230 volt models

after a delay of approximately 5 seconds.

4. Disconnect the dispenser from the power source.

If voltage was present as described, proceed to #5.
If voltage was not present as described, refer to the Wir-
ing Diagrams and check the dispenser wiring harness.

5. Remove both wires from the solenoid valve coil

terminals.

6. Check for continuity across the solenoid valve coil

terminals.

If continuity is present as described, reconnect the wires
and proceed to #7.
If continuity is not present as described, replace the
solenoid valve coil.

7. Check the solenoid valve for coil action. Connect

the dispenser to the power source. Listen carefully
in the vicinity of the solenoid valve for a “clicking”

FIG. 14a SOLENOID VALVE

FIG. 14b SOLENOID VALVE WIRING

WHI/BLU to Electronic
Control Board T1

P1778

WHI or RED to
Terminal Block

42311 071310

H 5