JLG 460SJ ANSI Parts Manual User Manual
Page 21
1-13
SECTION 1 FRAME
203
0641606
AR
Bolt 3/8in-16NC x 3/4in
8
Prior to SN 0300079125
16
SN 0300079125 to SN 0300096000
204
0681828
4
Bolt 1/2in-13NC x 3-1/2in
205
AR
Bushing, Garmax Options:
0961951
4
Prior to SN 0300079125 (Top & Bottom Kingpin Locations)
(Note: See Kit)
0440291
2
SN 0300079125 to SN 0300096000 (Top Kingpin Location)
0440274
2
SN 0300079125 to SN 0300096000 (Bottom Kingpin
Location)
206
0962140
2
Bearing, Garmax
207
1
Steer Cylinder Assembly Options (See CYLINDER SECTION
for Breakdown):
Use 1684412
Prior to SN 0300087392 (was p/n 1683614)
1684412
SN 0300087392 to SN 0300096000 (was p/n 1001140283)
208
3312008
4
Nut 5/8in-11NC
209
3322201
2
Nut 3/4in-16NF
210
4
Kingpin Options:
3422716
Prior to SN 0300079125 (2 Bolt Mounting) (Note: See Kit)
3423081
SN 0300079125 to SN 0300096000 (4 Bolt Mounting)
211
Use 3841517
2
Rod-End (was p/n 3841367 Rod-End with p/n 7020180 Grease
Fitting)
Ref
Note: Qty (1) p/n 4740086 Thrustwasher required between
bottom of p/n 3841517 Rod-End and Tie Rod.
212
3900109
4
Screw, Shoulder
213
4060950
1
Shield, Frame (Prior to SN 0300072506 Only)
214
1
Spindle (Left Side) Options:
Use 4130403
Prior to SN 0300079125 (was p/n 4130368)
4130405
SN 0300079125 to SN 0300096000
215
1
Spindle (Right Side) Options:
Use 4130404
Prior to SN 0300079125 (was p/n 4130369)
4130406
SN 0300079125 to SN 0300096000
216
4740086
4
Thrustwasher
217
4751800
4
Flatwasher 1/2in Regular
218
4846070
2
Tie-Rod
219
3780182
2
O-Ring (SN 0300079125 to SN 0300096000 Only) (Bottom
Kingpin Location Only)
220 to 223
Not Used
224
3020029
AR
Grease, Bearing
— — — — — — — — — —
300
2902400
Kingpin and Bushings Update Kit for Machines Built Prior to
SN 0300079125 (Includes Newer “SN 0300079125 to
SN 0300096000” Design Items 202, 203, 205, 210 and 219).
See Field Service Bulletin AWP-04-11.
Ref
Note: Newer bushings will fit in “Prior to SN 0300079125”
axles however if kingpin holes measure 1.503in diameter or
larger in any direction, axle weldment must be replaced
before installation of kit.
Note: Spindles require drilling and tapping for 8 additional
kingpin mtg bolts. Newer design kingpins require 4 mtg
bolts each.
FIGURE 1-3. AXLE & STEERING INSTALLATION - 4WD (CONTINUED)
ITEM #
PART NUMBER
QTY.
DESCRIPTION
REV.