JLG 500RTS ANSI Service Manual - Manual (Page 9)

SECTION 1 - SPECIFICATIONS
3121103 – JLG Sizzor – 1-1
SECTION 1. SPECIFICATIONS
1.1 CAPACITIES
Hydraulic Oil Tank
Approximately 36.5 U.S. gallons (138.17 liters) w/10% air
space.
Hydraulic System (Including Tank)
Approximately 44 U.S. gallons (166.56 liters).
Fuel Tank
Approximately 15 U.S. gallons (56.8 liters)
Engine Crankcase
Gasoline Engine
3.4 quarts (3.2 liters) w/filter
2.9 quarts (2.7 liters) w/o filter
Diesel Engine
6.34 quarts (6.0 liters) w/filter
5.8 quarts (5.5 liters) w/o filter
Coolant Capacity (Gasoline Engine)
3.5 U.S. gallons (13.2 liters)
1.2 COMPONENT DATA
Gasoline Engine
Displacement - 4.5 liter
Manufacturer/Model - Ford LRG-425
Oil Capacity
4.5 quarts (4.3 liters) w/ filter
4.0 quarts (3.8 liters) w/o filter
Low RPM - 750
Mid RPM - 2200
High RPM - 3000
Alternator - 55 Amp external
Battery - 85 Amphour, 550 Cold Cranking Amps
Fuel Consumption
Low RPM - 1.8 gph (6.7 lph)
High RPM - 3.0 gph (11.4 lph)
Horsepower - 70 @ 2800 RPM
Coolant Capacity - 3.5 U.S. gallons (13.2 liters)
Diesel Engine
Manufacturer/Model - Deutz F3L-1011
Oil Capacity
6.34 quarts (6.0 liters) w/filter
5.8 quarts (5.5 liters) w/o filter
Mid RPM - 2000
High RPM - 3000
Alternator - 60 Amphour
Battery - 60 Amphour, 1000 Cold Cranking Amps
Fuel Consumption
Low RPM - 1.9 gph (7.19 lph)
High RPM - 2.5 gph (9.46 lph)
Horsepower - 42 @ 3000 RPM
Drive/Steer System
Tires
Standard - 12 x 16.5 NHS, 8 ply, pneumatic, inflate to 45
PSI (3.1 bar)
Optional - 31 - 15.5 x 15 NHS, 8 ply, pneumatic, inflate to
35 PSI (2.4 bar)
Optional - 12 - 16.5 NHS, 6 ply, foam filled
Steer System
Toe-In - Adjust to 1/4 inch (6.4 mm) overall
Drive Motors/Hubs/Brakes
Drive Motor - 2.48 in.3 (6.3 cm3) displacement
Drive Hub (2WD Gasoline and Diesel Engine - Rear) - Hub
ratio 35:1
Drive Hub (4WD Rear) - Hub ratio 24:1
Drive Hub/Brake (4WD Front) - Hub ratio 24:1; brake -
spring applied, hydraulic release, release pressure - 160
psi (11 bar) initial, 190 psi (13 bar) full
Drive Brake (2WD/4WD Rear) - Spring applied, hydraulic
release, release pressure - 150 psi (10 bar) initial, 170 psi
(12 bar) full
NOTE: Wheel lugs should be torqued to 80 ft lb (109 Nm) at
50 hour intervals.
When maintenance becomes necessary or a fas-
tener has loosened, refer to the Torque Chart, Fig-
ure 1-1, to determine proper torque value.