Apple iMac G3 (DV) - Manual (Page 31)

m ATB0 (ITU/CCITT operation)
m AT&G0 (no guard tone)
m AT&P1 (33/66 pulse dial make/break ratio)
m ATS0 = 0 or ATS0 = 1 (no answer or answer greater than one ring)
m ATS6 = 95 (DTMF period between 70–255 ms)
m ATS11 = 95 (DTMF period between 70–255 ms)
For calls that are automatically generated, a total of three call attempts are allowed to a
telephone number, with a minimum period between calls of 2 seconds. If the call does
not connect after three attempts, 30 minutes must expire before automatic redialing
may be initiated. Failure to set the modem (and any associated communications
software) to the above settings may result in the modem being non-compliant with
Australian telecommunications standards. Under these circumstances a user could be
subject to significant penalties under the Telecommunications Act 1997.
This modem must be properly secured in order for you to use it. Telecommunications
network voltages exist inside the computer and the telecommunications line
connection must be removed before opening the computer.
Information you need in New Zealand
This modem is fully approved to operate on the New Zealand telecommunications
network under Telepermit number PTC 211/98/119. All telecommunications devices
are required to hold a Telepermit and be labelled accordingly with the approved
Telepermit number to comply with the New Zealand telecommunications standards,
ensuring the health and safety of the operator and the integrity of the New Zealand
telecommunications network.
Customers in New Zealand who are prompted to choose a country for their modem
should choose the “Australia” country code setting.
To ensure compliance, all calls that are automatically generated should not make
more than 10 call attempts to the same number within any 30 minute period with a
minimum period between calls of 30 seconds. Failure to adhere to these standards
may result in the modem being non-compliant with New Zealand Telecom standards.
Under these circumstances a user could be subject to significant penalties.
If pulse dialing is required for any reason, the communications software must be set
up to record numbers according to the following translation list.
m Number to be dialed: 0; number to be entered into computer: 0
m Number to be dialed: 1; number to be entered into computer: 9
m Number to be dialed: 2; number to be entered into computer: 8
m Number to be dialed: 3; number to be entered into computer: 7
m Number to be dialed: 4; number to be entered into computer: 6
m Number to be dialed: 5; number to be entered into computer: 5
m Number to be dialed: 6; number to be entered into computer: 4
m Number to be dialed: 7; number to be entered into computer: 3
m Number to be dialed: 8; number to be entered into computer: 2
m Number to be dialed: 9; number to be entered into computer: 1
m Number to be dialed: 0; number to be entered into computer: 0
The preferred method of dialing is to use DTMF tones as this is faster than pulse
(decadic) dialing and is readily available on almost all New Zealand telephone
exchanges.
Laser information
Warning Making adjustments or performing procedures other than those specified
in your equipment’s manual may result in hazardous radiation exposure.
Do not attempt to disassemble the cabinet containing the laser. The laser beam used
in this product is harmful to the eyes. The use of optical instruments, such as
magnifying lenses, with this product increases the potential hazard to your eyes. For
your safety, have this equipment serviced only by an Apple-authorized service
provider.
Service warning label
High-risk activities warning
This computer system is not intended for use in the operation of nuclear facilities,
aircraft navigation or communications systems, or air traffic control machines, or for
any other uses where the failure of the computer system could lead to death, personal
injury or severe environmental damage.
Mouse information
This product complies with the requirements of European Directives 72/23/EEC and
89/336/EEC. Complies with the Canadian ICES-003 Class B specification.
31