Philips FWC85C37 - Manual (Page 19)

3139 116 19591 (ENG)
19
STANDBY ON
MINI HIFI SYSTEM
BAND C 1 • 2 • 3 CDR
STOP •CLEAR SEARCH• TUNING PLAY PAUSE PREV NEXT
DUB (HSD) RECORD A. REV DIM CLOCK/
TIMER PROG
BASS TREBLE
wOOx TECHNOLOGY
POWER SAVE
IR SENSOR
SIDE VOLUME
PLUS LEVEL
PRESET ▲ ▲ BASS/ TR EB LE
TAPE CD TUNER AUX
P E R S O N A L
D S C
VE C
TAPE 1•2 CD 1•2•3 FM•AM CDR/DVD
Note:
– For 'EASY SET' feature, please refer to
page 13.
Tuning to radio stations
1 Press TUNER (FM•AM) to select
TUNER mode.
™ "TUNER" will be displayed.
A few seconds later, the current
radio frequency will be displayed.
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press à or á for more than one
second, then release.
™ The display will show "SEARCH"
until a radio station with sufficient
signal strength is found.
• Repeat this procedure until the
desired radio station is reached.
• To tune to a weak radio station,
briefly press à or á repeatedly
until the display shows the desired
frequency and/or when the best
reception has been obtained.
Storing Preset Stations
You can store up to 40 radio stations in
the memory. When a preset radio
station is selected, the preset number
appears next to the frequency on the
display.
Automatic programming
1 Press TUNER (FM•AM).
2 Press PROG for more than one
second.
™ The
PROGRAM starts flashing and
" AUTO" will be displayed.
TUNER
™ The system will search for every
available radio station in the FM
waveband first, then search the
AM waveband.
™ All available radio stations will be
stored automatically. The
frequency and preset number will
be displayed briefly.
™ The system will stop searching
when all the available radio stations
are stored or when the memory
for 40 preset radio stations is used.
™ The system will remain tuned to
the last stored preset radio station.
Notes:
– You can cancel the automatic
programming by pressing PROG orÇ
(on the system only).
– If you want to reserve a section of
preset numbers, for example preset
numbers 1 to 9, select preset 10
before starting automatic programming,
only the preset numbers 10 to 40 will
be programmed.
Manual programming
1 Press TUNER (FM•AM).
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press PROG for less than one
second.
™ The
PROGRAM starts flashing.
™ The next available preset number
will be displayed for selection.
4 Press à or á to tune to the
desired frequency.
• If you wish to store the radio station
to another preset number, press 4
or 3 (or Digit 0-9 on the remote
control) to select the desired preset
number.
5 Press PROG again.
™ The PROGRAM disappears and the
radio station will be stored.
• Repeat steps 3 – 5 to store other
preset radio stations.
Notes:
– When 40 radio stations are stored and
you attempt to store another radio
station, the display will show
"
PROGRAM FULL". If you want to
change an existing preset number,
repeat steps 3 – 5.
– You can cancel manual programming
by pressing Ç (on the system only).
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Tuning to Preset Radio
Stations
• Press 4 or 3 (or Digit 0-9 on the
remote control) to select the desired
preset number.
™ The preset number, radio
frequency, and waveband appear
on the display.
pg 01-28/C85/37-Eng 2/16/00, 9:03 AM 19