Philips CDR760BK - Manual (Page 19)

17
English
Selecting a track during play
1 Briefly press ∞ or § one or more times.
➜ Play skips to the beginning of the present, previous or
following track.
or
• Press the required track number using the numerical keys
on the remote control. For 2-digit track numbers, press the
keys in rapid succession.
➜ Play skips to the beginning of the selected track.
Selecting a track when CD play is stopped
1 Briefly press ∞ or § one or more times.
2 Press PLAY.
➜ Play starts at the selected track.
or
• Press the required track number using the numerical keys
on the remote control. For 2-digit track numbers, press the
keys in rapid succession.
Searching during CD play
1 Hold down ∞ or § (or 5 or 6 on the remote control).
➜ The player first searches backwards or forwards at 10
times normal speed with sound at low volume, then
goes to fast reverse or fast forward with sound muted.
2 Release the button at the desired passage.
➜ Play starts at the desired passage.
Note: During Shuffle, Repeat or Program play, search is
restricted to within the track being played at the time.
1 Press SHUFFLE (or PLAY) on the remote control before or
during CD play to start shuffle play.
➜ The tracks on the CD (or program if set) play in random
order. SHUFFLE will appear on the display between
tracks.
2 Press SHUFFLE again to return to normal CD play.
Note: Shuffle is also cleared when you open the disc tray.
1 Press REPEAT on the remote control one or more times
during CD play.
➜ When
REPEAT 1 appears on the display, the current track
plays repeatedly. When REPEAT appears on the display,
the disc or program plays repeatedly.
2 To return to normal play, press REPEAT one or more times
until:
➜ the
REPEAT message disappears from the display.
Note:
- You can use shuffle in combination with repeat CD or
program play.
- Repeat is also cleared when you open the disc tray.
You can program up to 30 tracks to play in any desired
sequence. Tracks can be programmed more than once, but
each time counts as a track.
1 On the remote control press PROGRAM to start
programming.
➜
PROG flashes on the display.
2 Press a track number with the number keys. For 2-digit
numbers, press the keys in rapid succession.
➜ On the display, the track number appears briefly,
followed by the total programmed tracks and total
program time.
3 Repeat step 2 for all tracks to be programmed.
4 Press STOP or PROGRAM to end programming.
➜
PROG lights continuously.
Note:
- To review the program, press ∞ or § in stop mode.
- To add more tracks to the program, repeat steps 1 through
4.
- If you try to store more than 30 tracks, FULL appears on
the display
5 Press PLAY to start programmed play.
Clearing a program
1 Press STOP if necessary to stop programmed play.
2 Press STOP again to clear the program.
➜
PROG disappears from the display.
Note: The program is also cleared when you open the disc
SH UF FLE
O P E N /C LO S E
DISPLAY
PROGRAM
CDR
C D
1
2
3
4
5 7
8
6
y
5
Programming
Repeat CD, track or program
P R E V .
SH UF FLE
R E P E A T
O P E N /C LO S E
AY
CD R
C D
1
2
3
4
5 7
8
0
6
9
y
S T O P
P L A Y
5
6
Shuffle play
Power On/Off
CD-Sync
C D - R E C O R D A
B L E / R E
W R I T A B L E
RECORD
PLAY
PAUSE
STOP
FINALIZE
ERASE
Recordable
Selecting a track or searching
PLAYING