Behringer SL2442FX-PRO - Manual (Page 10)

10
EURODESK SL3242FX - PRO
/SL2442FX - PRO
The CD/TAPE OUTPUT RCA connectors provide the stereo
main mix signal to a tape deck or DAT recorder to record
your mix. The signal is taken pre-fader, so that it will not be
influenced by the fader positions.
2.8 Master aux send 1 and 2
Fig. 2.22: Master aux sends
These are the master AUX SEND controls 1 and 2 for
adjusting the volume level sent to the corresponding aux
send connectors (see ). This way, you can control the
mix of all AUX 1 or AUX 2 signals of the input channels. The
AUX SEND section also has a SOLO switch.
Fig. 2.23: Master aux send outputs
Use the AUX SEND outputs 1 and 2 to take the master AUX
SEND signals and route them to an external effects device
or your monitor speakers. Subsequently, you can return
the effect signal, e.g. via the STEREO FX RETURN inputs
(see ) or specific input channels.
2.9 Graphic 9-band stereo equalizer
Fig. 2.24: The graphic stereo equalizer
Your EURODESK is equipped with a graphic 9-band stereo
equalizer processing either the main or the AUX 1 signal.
Use the EQ to adapt the sound to the room acoustics.
Use the EQ IN switch to switch the equalizer on. In this
case, the fader LEDs illuminate.
With the MAIN/AUX 1 switch you can determine the signal
to be processed, either MAIN or AUX 1.
Press the FBQ IN switch to activate the FBQ Feedback
Detection System. The frequencies causing
feedback are indicated by the brightly lit fader
LEDs, while all other LEDs are darker. Simply
lower the level of the brightly lit faders until
feedback disappears.
2.10 Effects section
Fig. 2.25: The digital effects processor
Here you will find a list of all multi-effects presets (see also
chapter 3 “DIGITAL EFFECTS PROCESSOR”).
The FX LED level meters show the effects processor’s
input signal. Be sure that the clip LED only illuminates with
signal peaks. If it is lit all the time, the effects processor is
overloading and hence producing unpleasant distortion.
The EFFECT displays show the currently selected presets.
This is the master FX 1 (or 2) SEND control for adjusting
the volume of all FX send signals at the corresponding FX
send jacks (see ) and at the inputs of the built-in effects
processor. Use it to control the master signal of all
FX 1/FX 2 signals from the input channels. When neither of
the FX SEND controls is turned up, the effects processor
will not receive a signal.
Turn the FX 1 (or FX 2) control to select an effects preset.
Then, push it briefly to confirm your selection and activate
the new effect.
The FX 1 (or 2) TO AUX 1 controls allow you to add the
effect signal from the built-in effects processor (FX1 or
FX2) to the AUX 1 monitor signal. Naturally, the effects
processor must be provided with an input signal (i.e. the
FX controls in the channel strips plus the FX SEND controls
and the channel faders must be turned up).
This is the FX 1 (or 2) TO AUX 2 control adding the effect
signal from the effects processor to the AUX 2 monitor signal.
See for further details.
The FX 1 (or 2) TO MAIN control routes the effect signal
either to the main mix or the subgroups 1 and 2 (or 3 and
4), depending on the position of the selector switch (see
). When it is hard left, no effect signal will be audible.
Here, too, the FX controls in the channel strips plus the FX
SEND controls and the channel faders must be turned up.
These selector switches route the effect signal to the main
mix or to the subgroups 1-2 or 3-4. If the MAIN/SUB switch
is not pressed, the effect signal is sent to the main mix and
the SUB 1/2 / SUB 3/4 switch below is inoperative. If the
upper switch is pressed (SUB), however, the lower switch
determines whether the effect signal is routed to
subgroups 1 and 2 (SUB 1/2) or 3 and 4 (SUB 3/4).
2. CONTROL ELEMENTS