Neff S66M63N1GB User Manual
Neff Washers
Table of contents
Document Outline
- ( Safety instructions 4
- 7 Protection of the environment 8
- * Getting to know your appliance 8
- + Water softening system/Special salt 9
- , Rinse aid 10
- - Utensils 12
- . Detergent 14
- / Overview of programmes 17
- 0 Additional options 18
- 1 Operating the appliance 19
- 2 Cleaning and maintenance 21
- 3 Fault, what to do? 23
- 4 Customer service 32
- 5 Installation and connection 32
- 8 Intended use
- Intended use
- ( Safety instructions
- Children from 8 years of age or people whose physical, sensory or mental abilities or their lack of experience or knowledge prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible p...
- Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance.
- Retain all documents for subsequent use or for the next owner.
- Delivery
- 1. Check the packaging and dishwasher immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier.
- 2. Please dispose of the packaging material in an environmentally friendly manner.
- 3. Do not let children play with packaging and its parts. There is a risk of suffocation from collapsible boxes and film.
- Installation
- In daily use
- Childproof lock (door lock)Door lock *
- Childproof lock (button lock)Button lock
- You can secure your appliance from being unintentionally the programme terminated (e.g. improper operation by children).
- Activating the button lock:
- If any button is pressed while the programme is running, this ’– is indicated on the digital display. It is not possible to end (Reset) the programme.
- Deactivating the button lock:
- When the programme ends (‹:‹‹ on the digital display), the button lock is cancelled. If there is a power failure, the button lock is retained. Whenever a programme is restarted, the button lock must be reactivated.
- Damage
- Disposal
- 1. Make redundant appliances unusable to prevent subsequent accidents.
- 2. Dispose of the appliance in a n environmentally friendly manner.
- m Warning
- Risk of injury!
- m Warning
- Risk of explosion!
- m Warning
- Risk of scalding!
- m Warning
- Risks to children!
- 7 Protection of the environment
- Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials.
- Please dispose of the individual parts separated according to type.
- Please ask your dealer or inquire at your local authority about current means of disposal.
- All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g. >PS< polystyrene). Therefore, plastic waste can be sorted out when the appliance is being disposed of.
- Please follow the safety instructions under “Delivery”.
- Old appliances
- Please follow the safety instructions under “Disposal of your appliance”.
- This appliance is identified according to the European guideline 2002/96/EC on waste electrical and electronic equipment – WEEE. The guideline specifies the framework for an EU-wide valid return and re-use of old appliances.
- Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front.
- Individual positions are referred to in the text.
- ON/OFF switch
- Programme buttons **
- Display “Check water supply”
- Salt refill indicator
- Rinse aid refill indicator
- Timer programming *
- Additional options **
- START button
- Programme sequence indicator
- Digital display
- * depending on model
- ** Number depending on model
- Appliance interior
- Top basket
- Top spray arm
- Bottom spray arm
- Filters
- Dispenser for special salt
- Cutlery basket
- Bottom basket
- Dispenser for rinse aid
- Detergent dispenser
- Lock for detergent dispenser
- Rating plate
- * depending on model
- To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container.
- Tap water above 1.2 mmol/l must be softened. The water is softened with special salt (regeneration salt) in the water softening system of the dishwasher.
- The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table).
- The amount of salt dispensed can be set from •:‹‹ to •:‹ˆ.
- Salt is not required at the set value •:‹‹.
- 1. Find out about the hardness value of your tap water. Your water utility company will help you with this.
- 2. Set value can be found in the water hardness table.
- 3. Close the door.
- 4. Switch on ON/OFF switch (.
- 5. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
- 6. Release both buttons.
- To change the setting:
- Water hardness table
- Using special salt
- Using detergents with salt componentDetergents with salt component
- Switching off salt refill indicator/water softening systemSwitching off water softening system
- If the salt refill indicator @ is impaired (e.g. when using combined detergents containing salt component), it can be switched off.
- As soon as the rinse-aid refill indicator H is lit on the fascia, there is still a rinse-aid reserve of 1-2 rinsing processes. Refill with rinse aid.
- The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers.
- Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used.
- 1. Open the dispenser 1Z by pressing and lifting the plate on the cover.
- 2. Carefully pour rinse aid up to the max. mark in the filler opening.
- 3. Close cover until it clicks shut.
- 4. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth.
- Setting amount of rinse aid
- The amount of rinse aid dispensed can be set from §:‹‹ to §:‹‡. This is the factory setting §:‹….
- Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select higher setting) are left on the utensils.
- 1. Close the door.
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
- 4. Release both buttons.
- 5. Press programme button # until the factory set value §:‹… is indicated on the digital display )".
- To change the setting:
- Switching off rinse aid refill indicator
- If the rinse-aid refill indicator H is impaired (e.g. when using combined detergents containing rinse aid component), it can be switched off.
- The rinse aid refill indicator H is now switched off.
- Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles.
- Glass and utensil damage
- Loading the dishwasher
- Unloading the dishwasher
- To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom up.
- Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
- Cups and glasses
- Pans
- Cutlery basket
- Folding spikesFolding spikes *
- Small accessories holder *Small accessories holder
- Height of utensils
- If required, the top utensils basket 1" can be taken out in order to create more space in the bottom basket for taller utensils.
- You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately l...
- Adding detergent
- Combination detergent
- Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5i...
- As soon as combined detergents are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result.
- / Overview of programmes
- Overview of programmes
- The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
- Programme selection
- Information for test institutes
- Test institutes receive the information for comparability tests (e.g. according to EN60436).
- These are the conditions for conducting the tests, however these are not the results or consumption values.
- Request by e-mail to:
- [email protected]
- The product number (E no.) and the production number (FD) are required which you can find on the rating plate 9" on the appliance door.
- * depending on model
- Additional options can be set with the buttons X.
- This function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. The change in the running time is indicated on the digital display )". To obtain optimum cleaning results at a reduced running time, water and ...
- · Hygiene *Hygiene
- Ï Intensive zone *Intensive zone
- ¿ Extra drying *Extra drying
- An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption.
- The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result...
- Aqua sensorAqua sensor *
- * depending on model
- The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
- The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 2–4 litres. If the turbidity is greater, the water is drai...
- Switching on the appliance
- Programme sequence indicatorProgramme sequence indicator h
- Remaining running time display
- When the programme is selected, the remaining running time of the programme is indicated on the digital display )".
- The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
- Timer programmingTimer programming *
- * depending on model
- You can delay the start of the programme in 1-hour steps up to 24 hours.
- 1. Close the door.
- 2. Switch on ON/OFF switch (.
- 3. Press button P + until the digital display )" jumps to œ:‹‚.
- 4. Press P + or – button until the displayed time corresponds with your requirements.
- 5. Press START button `, timer programming is activated.
- 6. To delete timer programming, press the P + or – button until )" œ:‹‹ is indicated on the digital display.
- End of programme
- Switching off automatically after the end of the programme *Switching off automatically after the end of the programme
- * depending on model
- To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting).
- Automatic disconnection can be adjusted from ˜:‹‹ to ˜:‹ƒ.
- Appliance does not switch off automatically
- Off after 1 min
- Off after 120 min
- Switching off the appliance
- Interrupting the programme
- Terminating the programmeTerminating the programme (Reset)
- Changing the programme
- Intensive drying
- The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!)
- 1. Close the door.
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until the digital display )" •:‹... is indicated.
- 4. Release both buttons.
- 5. Press programme button # until the factory set value š:‹‹ is indicated on the digital display )".
- To change the setting,
- 2 Cleaning and maintenance
- A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems.
- If you find such deposits:
- Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers.
- Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage.
- Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces.
- Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
- The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!)
- Special salt and rinse aid
- Filters
- The filters 1: keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters.
- The filter system consists of a coarse filter, a flat fine filter and a microfilter.
- 1. After each washing cycle check the filters for residue.
- 2. Unscrew filter cylinder as illustrated and take out filter system.
- 3. Remove any residue and clean filters under running water.
- 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system.
- Spray arms
- Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1* and 12.
- Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful informa...
- Waste water pump
- Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter.
- In this case:
- 1. First disconnect the appliance from the power supply.
- 2. Remove the filters 1:.
- 3. Scoop out water, use a sponge if required.
- 4. Loosen screws on the pump cover (Torx T 20) and pull off.
- 5. Check inner compartment and remove any foreign objects.
- 6. Place pump cover in the original position, press down and screw tight.
- 7. Install filters.
- Fault table
- If you are unable to rectify the fault, please contact your customer service. We always find a suitable solution, even to avoid unnecessary visits by technicians. Contact information for your nearest customer service can be found on the back of these...
- Rely on the competence of the manufa cturer. Contact us. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your domestic appliances.
- The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragr...
- Install the appliance in the correct sequence:
- If you have any complaints, contact the dealer where you purchased the appliance or our customer service.
- * depending on model
- Safety instructions
- Delivery
- Technical specifications
- Weight:
- max. 27 kg
- Voltage:
- 220–240 V, 50 Hz or 60 Hz
- Connected load:
- 2.0–2.4 kW
- Fuse:
- 10/16 A (UK 13A)
- Power input:
- switched off 0.1 W
- not switched off 0.1 W
- Water pressure:
- at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
- Inlet rate:
- minimum 10 litres/minute
- Water temperature:
- Preferably cold water; if hot water, depending on type of water inlet hose, max. temp. 60 °C (see Fresh water connection).
- Installation
- Waste-water connection
- Fresh water connection
- 1. Connect the fresh-water connection to the tap according to the installation instructions with the enclosed parts.
- 2. When replacing the appliance, always use a new water supply hose.
- Water pressure:
- at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
- Inlet rate:
- minimum 10 litres/minute
- Water temperature:
- Note printing on the water inlet hose!
- If models are marked with 25°, the water temperature may be max. 25 °C (cold water).
- For all other models:
- cold water preferred; hot water max. temperature 60 °C.
- Warm water connection *Warm water connection
- * depending on model
- The dishwasher can be connected to cold or hot water up to max. 60 °C.
- Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation, e.g. solar heating system with circulation line.
- This will save energy and time.
- The hot water setting ‘:‹‚ allows you to adjust your appliance optimally to operation with hot water.
- It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C.
- It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler.
- Electrical connection
- Removing the appliance
- Transportation
- Empty the dishwasher and secure loose parts.
- Drain the appliance according to the following steps:
- 1. Turn on the tap.
- 2. Close the door.
- 3. Switch on ON/OFF switch (.
- 4. Select programme with the highest temperature.
- 5. Press START button `.
- 6. After approx. 4 minutes press the START button ` until ‹:‹‚ is indicated on the digital display.
- 7. Switch off ON/OFF switch (.
- 8. Turn off the tap, disconnect supply hose and drain water.
- Drain the appliance according to the following steps:
- Transport appliance upright only.
- (This prevents residual water from running into the machine control and damaging the programme sequence.)
- Empty the dishwasher and secure loose parts.
- Protection against frostProtection against frost (Emptying the appliance)