Neff W7460X1GB User Manual
Washing machine
Table of contents
Document Outline
- Your new washing machine
- Display rules
- Contents
- en Instruction Manual and Installation Instructions
- 8 Intended use 4
- ( Safety instructions 5
- 7 Environmental protection 7
- * Getting to know the appliance 8
- Z Laundry 10
- C Detergent 11
- 0 Programme default settings 12
- \ Additional programme settings 13
- 1 Operating the appliance 14
- H Sensors 18
- M Setting the signal 19
- 2 Cleaning and maintenance 20
- 3 Faults and what to do about them. 22
- 4 After-sales service 25
- J Technical data 26
- 5 Positioning and connecting 26
- 8 Intended use
- en Instruction Manual and Installation Instructions
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- Risk of injury!
- 7 Environmental protection
- * Getting to know the appliance
- Z Laundry
- Laundry
- Prepare the laundry
- Sorting laundry
- Starching
- Dyeing/bleaching
- Soaking
- 1. Pour soaking agent/detergent into compartment II according to the manufacturer’s instructions.
- 2. Turn the programme selector to the Cottons 30 °C programme.
- 3. Press the start button.
- 4. After approx. 10 minutes, press the start button again to pause the programme.
- 5. After the required soaking time, press the start button again, if the programme is to be continued or changed.
- Notes
- C Detergent
- 0 Programme default settings
- Programme default settings
- Note:
- Temperature
- Spin speed
- Ready in time
- 1. Select the required programme.
- Note:
- 2. Press the Ready in button repeatedly until the required number of hours is displayed in the display panel.
- 3. Press the Start button.
- 1. Press the Start button.
- 2. YES and v lights up in the display panel. The washing machine door can be opened and laundry can be added.
- 3. Close the washing machine door.
- 4. Press the Start button again. The preselected time continues to run.
- \ Additional programme settings
- 1 Operating the appliance
- : Warning
- : Warning
- Eye/skin irritation!
- Note:
- 1. Pull out the detergent drawer as far as possible.
- 2. Add detergent and/or care products.
- 3. Close the detergent drawer.
- 1. Pull out the detergent drawer. Press down the insert and fully remove the drawer.
- 2. Slide the measuring aid forwards, fold it down and click it into place.
- 3. Reinsert the drawer.
- Note:
- Note:
- Start the programme
- Childproof lock
- Adding laundry
- Changing the programme
- Cancel the programme
- Programme end
- Removing laundry/switching off the appliance
- H Sensors
- M Setting the signal
- 2 Cleaning and maintenance
- Eye/skin irritation!
- : Warning
- : Warning
- Risk of poisoning!
- Machine housing/control panel
- Drum
- Descaling
- Detergent drawer and housing
- 1. Pull out the detergent drawer. Press down the insert and fully remove the drawer.
- 2. To remove the insert: Push the insert upwards from below with your finger.
- 3. Clean the detergent dispenser tray and insert with water and a brush, and dry it. Clean the inside of the housing as well.
- 4. Fit the insert and lock it in place (push the cylinder onto the guide pin).
- 5. Push in the detergent drawer.
- Note:
- Detergent solution pump blocked
- : Warning
- Risk of scalding!
- 1. Turn off the water tap so that no more water can flow in and has to be drained via the detergent solution pump.
- 2. Switch off the appliance and pull out the mains plug.
- 3. Open and remove the service flap.
- 4. Fold out the water gutter in front of the pump cover.
- 5.
- 6. Now carefully unscrew the pump cover. Residual water may run out.
- 7. Fold in the water gutter.
- 8. Place the service flap back on, lock it into place, and close it.
- Note:
- The drain hose at the siphon is blocked
- Filter in the water supply blocked
- 1. Turn off the tap.
- 2. Select any programme (except Rinse, Spin, Empty.
- 3. Press the Start button. Allow the programme to run for approximately 40 seconds.
- 4. Set the programme selector to the Off position. Remove the mains plug.
- 5. Clean the filter on the water tap:
- 6. For standard and Aqua-Secure models, clean the filter on the rear of the appliance:
- 7. Connect the hose and check for leaks.
- 3 Faults and what to do about them.
- Risk of scalding!
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- Danger of death!
- Before washing for the first time
- Notes
- 1. Check the machine.
- 2. Plug in the mains plug.
- 3. Turn the tap on.
- 4. Close the washing machine door (do not load any laundry).
- 5. Select the Cottons programme and 90 °C as the temperature.
- 6. Open the detergent drawer.
- 7. Pour approx. 2 litre of water into compartment II.
- 8. Pour standard detergent into compartment II.
- Note:
- Notes
- Transportation
- 1. Turn off the water tap.
- 2. Reduce the water pressure in the supply hose.
- 3. Drain the remaining detergent solution.
- 4. Disconnect the washing machine from the mains.
- 5. Remove the hoses.
- 1. Remove the covers and keep in a safe place.
- 2. Insert all four sleeves.
- Notes
- 1. If water damage is caused due to a fault in our Aqua-Stop system, we will compensate domestic customers for the damage caused.
- 2. The liability guarantee is valid for the service life of the appliance.
- 3. It is a prerequisite of all warranty claims that the appliance with Aqua-Stop must have been installed and connected correctly in accordance with our instructions; this also includes a correctly fitted Aqua-Stop extension (genuine accessories).
- 4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured afterwards by turning off the tap.