Sharp HT-SB32D Barre de son - Manual

Remote control battery installation
TINSEA348AWZZ
MODEL
HT-SB32D
SOUND BAR HOME THEATRE SYSTEM
This Quick Start Guide will help you to correctly install and operate your system.
Remote control × 1 RCA cable
(2 pins - 2 pins) × 1
AC power lead × 1 Foot cushion × 4
AC/DC adaptor × 1 Wall mount angle × 2
Nut
(Spike + Nut) × 4
(Length: 25 mm) Pattern paper × 1
Accessories
Turn on your system
Before using remote control
Before using remote control, please remove plastic
shield at battery holder.
Battery holder
Plastic shield
Remote control
1
Press the ON/STAND-BY button.
The sound mode indicator and display light up. If the
power does not turn on, check whether the power
cord is plugged in properly.
2
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
The STAND-BY indicator turns red.
Polarity (+) symbol
Printed in Malaysia
11A R AS 1
1
Insert pin into the hole as shown and pull to open the
battery holder.
Battery holder
Locking tab
Battery type
Positive (+) side up
2
Remove the old battery from the battery holder,
insert the new battery and then slide the battery
holder back into the remote control.
Back of remote
control
Pin
HT-SB250W250BK (QG).indd 1 12/29/2010 5:07:22 PM
Accessories
MUTE
ON/ STAN D-BY
MUSI C
CINEM A
NEWS
SURR OUND BYPA SS
INPU T
TV CH
VOL VOL
RRMCG A322A WSA
SOUN D MO DE
Remote control x 1 AC/DC adaptor x 1
(RADPA100AWZZ)
Optical cable x 1 Pattern paper x 1
Velcro tape (hook type) x 1 Velcro tape (loop type) x 2
HT-SB32D
AC power lead x 1 NFC tag x 1
Spike leg x 2
Before using remote control
Before using the remote control, remove the
plastic shield from the battery holder.
Remote control Plastic shield
Battery holder
Turn on your system
Press the ON/STANDBY button.
The On/Standby/Input indicator lights up according to input
source:
Input source On/Standby/Input
indicator
OPTICAL IN Turns green
AUDIO IN Turns cyan
Bluetooth Turns blue
Note:
If the power does not turn on, check whether the power lead is
plugged in properly.
To set the sound bar to standby mode:
Press the ON/STANDBY button again. The PAIRING indicator
turns BLUE.
AC power connection
1 Plug the AC power lead into the AC/DC
adaptor.
2 Plug the AC/DC adaptor cable into the DC
INPUT socket on the sound bar.
3 Plug the AC power lead into a wall socket. The
PAIRING indicator turns BLUE.
14G R AS 1
TINSEA474AWZZ
Barcodesoft
http://www.barcodesoft.com
Barcode Symbology: Code 93 ; Font Facename: Code93MHr
Data To Encode: TINSEA474AWZZ
Point Size 8 :
*TINSEA474AWZZI3*|
Point Size 10 :
*TINSEA474AWZZI3*|
Point Size 12 :
*TINSEA474AWZZI3*|
Point Size 14 :
*TINSEA474AWZZI3*|
Make sure to unplug the AC power lead before
making any connections.
2
1
AC/DC Adaptor
Cable
DC IN socket
(DC 19V)
AC power lead
AC/DC Adaptor
(AC 100 - 240 V ~ 50/60 Hz)
Wall socket
HTSB32_QG.indd 1 2014-07-07 08:56:37