Bulldog Security RS602E - Manual (Page 12)

11
INSTALLATION PROGRAMMING:
Programming Tach/Tachless Start
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3)
times. Release Button #3. Press and release Button #4, the parking lights will flash once. The unit is
now in Tachless Start Mode. Press and release Button #4, the parking lights will flash twice. The unit is
now in Tach Start Mode. Release the brake, the parking lights will flash three (3) times. The programming
is now entered. NOTE: Factory setting is Tachless Start Mode.
Programming Door Lock Pulse Length
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3)
times. Release Button #3. Press and release Button #1, the parking lights will flash once, the door lock
pulse length is now 3.5 seconds. Press and release Button #1, the parking lights will flash twice, the
door lock pulse length is now .7 seconds. Release the brake, the parking lights will flash three (3) times.
The programming is now entered. NOTE: Factory Door Lock Pulse Setting is .7 seconds.
Programming Double Pulse Unlock Output (Factory Security Shutdown)
Press and hold the brake, then press and hold Button #4 (stop) until the parking lights flash four (4)
times. Release Button #4. Press and release Button #3, the parking lights will flash once. Double Pulse
Unlock is on. Press and release Button #3, the parking lights will flash twice. Double Pulse Unlock is now
programmed off. Release the brake, the parking lights will flash three (3) times. The programming is now
entered. NOTE: Factory Setting is Double Pulse off.
Programming Doorpin Inputs
Press and hold the brake, then press and hold Button #4, the parking lights will flash (4) times, release.
Now press and release Button #1. The parking lights will flash once, the unit is now programmed for a (+)
positive doorpin. Press and release Button #1 again, the parking lights will flash twice, the unit is now
programmed for a (-) negative doorpin.
OPERATOR PROGRAMMING:
Adding New Transmitters
Press and hold the brake, then press and hold Button #1 (start) until the parking lights flash once. Release
Button #1. Press any button on the new remote, the parking lights will flash three (3) times, the new
remote is now programmed.
Programming Lock with Brake, Unlock with Ignition Off
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three
(3) times. Release Button #3. Press and release Button #2, the parking lights will flash once. The unit
will now lock with the brake and unlock when the ignition is turned off. Press and release Button #2
again, the parking lights will flash twice. The Lock with Brake feature is now turned off. Release the
brake, the parking lights will flash three (3) times. The programming is now entered. NOTE: Factory
setting is Lock with Brake off.
Programming Automatic Start Options
Press and hold the brake, then press and hold Button #2 (arm/disarm) until the parking lights flash
twice. Release Button #2. Press and release Button #1, the parking lights will flash once. You are now
in 3 hour Start Mode. Your vehicle will start every three (3) hours. Press and release Button #1 a second
time. The parking lights will flash twice for Low Voltage Start. To discontinue automatic start options,
press and release Button #1 a third time. The parking lights will flash three (3) times, the Automatic
Start Option is now off. Release the brake, the parking lights will flash three (3) times. The programming
is now entered. NOTE: The factory setting is Automatic Start Option off.
Programming Cold Start
Press and hold the brake, then press and hold Button #2 (arm/disarm) until the parking lights flash
twice. Release Button #2. Press and hold Button #2, the parking lights will flash once. Each continuous
flash represents a progression in degrees: one (1) flash= -40ºF, two (2) flashes=-30ºF, three (3) flashes=-
20ºF, four (4) flashes=-10ºF, five (5) flashes=0ºF, six (6) flashes=10ºF, seven (7) flashes=20ºF. To
disable Cold Start, press and hold Button #2 until the parking lights flash seven (7) times, then two
(2) quick flashes 8 and 9. The Cold Start is now disabled. Release the brake, the parking lights will
flash three (3) times, the programming is now entered. NOTE: The factory setting is Cold Start off.
Programming Hot Start
Press and hold the brake, then press and hold Button #2 (arm/disarm) until the parking lights flash
twice. Release Button #2. Press and hold Button #3, the parking lights will flash once. Each continuous
flash represents a progression in degrees: one (1) flash=
160ºF, two (2) flashes=150ºF, three (3) flashes=140ºF, four (4) flashes=130ºF, five (5) flashes=120ºF,
six (6) flashes=110ºF, seven (7) flashes=100ºF. To disable Hot Start, press and hold Button #3 until
the parking lights flash seven (7) times, then two (2) quick flashes 8 and 9. The Hot Start is now
disabled. Release the brake, the parking lights will flash three (3) times, the programming is now
entered. NOTE: The factory setting is Hot Start off.