Toshiba RDXV59 - Manual (Page 19)

19 EN
In
tr
od
uct
ion
Connect
ions
P
lay
b
a
ck
E
d
it
in
g
O
th
e
rs
Fu
nct
ion
S
e
tu
p
Re
co
rd
in
g
V
H
S
Fu
nc
ti
on
s
Basi
c Se
tu
p /
TV
Vi
ew
Op
eration
Connecting to an External Equipment
This unit has three input terminals. Press
[INPUT SELECT
F] repeatedly to select the external input
mode, then press [PROG. G \ H] repeatedly to select AV1,
AV2 or DV(AV3). Be sure that all the units are switched off
before making connections.
Note
• When you record a TV programme from a Satellite Box, you
must connect a Scart cable to AV2 (DECODER). (See
page 37.)
• The signal from the external device will be output
automatically when the TV is connected to AV1 and the
external device is connected to AV2 using a Scart cable with
its power on (The signal from this unit cannot be monitored
except during playback.).
If you want to monitor this unit’s signal, press [DISPLAY]
or turn the external device off.
If you want to monitor the signal from other input, press
[DISPLAY], then press [INPUT SELECT
F] to select the
desired external input mode, then select the desired input
channel using [PROG.
G \ H].
When connecting a DV-camcorder, use DV input jack of
DV(AV3) (Front).
Digital Audio for Better Sound Quality
For clear digital sound quality, use the DIGITAL
AUDIO OUT (COAXIAL) jack to connect your digital
audio equipment.
If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a strong,
distorted sound or no sound at all.
• Connecting multi-channel Dolby Digital decoder allows you
to enjoy the Multi-channel Dolby Digital surround system as
well as DTS decoder, Multi-channel surround system.
• After connecting to a Dolby Digital decoder, set “Dolby
Digital” to “Stream” in “Audio Out” menu. (See page 69.)
• After connecting to a DTS decoder, set “DTS” to “ON” in
“Audio Out” menu. (See page 69.)
• After connecting to a MPEG decoder, set “MPEG” to
“Stream” in “Audio Out” menu. (See page 69.)
• The audio source recorded in Dolby Digital Multi-channel
surround format cannot be recorded using an MD or DAT
deck as a digital sound.
• If not connected to a Dolby Digital decoder, set “Dolby
Digital” to “PCM” in “Audio Out” menu. Playing back a DVD
using incorrect settings may generate noise distortion and
damage speakers.
• Set “Dolby Digital” and “MPEG” to “PCM” and set “DTS” to
“OFF” in “Audio Out” menu for connecting to an MD or DAT
deck.
• You can use AUDIO OUT (L \R) jacks for the connection of
your audio system.
Recording from a DVD player, Satellite
Box or other Audio-Video equipment
with a Scart output socket (AV2)
Recording from a DV-camcorder
(DV(AV3))
AV output jack
(Scart)
Scart cable (not supplied)
AV2 (DECODER)
OPEN/CLOSE
DUBBING VCR HDD DVD HDD DVD
PROGRAM
DUBBING
VCR DVD VCR HDD
SELECT HDD/DVD
DVD REC
DVD HDD
HDD DVD
USB DV IN
PAL
DV(AV3) (Front)
DV cable
(4-pin)
(not supplied)
DV OUT
The connections illustrated above are
optional for better sound.
Connecting a Dolby Digital™ decoder,
DTS decoder or MPEG decoder
Connecting to an MD deck or DAT deck
COAXIAL
COAXIAL
Dolby Digital decoder,
DTS decoder or
MPEG decoder, etc. Digital audio
input jack
Coaxial cable
(not supplied)
E3TK2BD_EN.book Page 19 Thursday, April 16, 2009 12:00 PM