Konica Minolta bizhub 20 - Manual (Page 3)

2
CAUTION
After you have just used the machine, some internal parts of the machine will be extremely hot. When you
open the front or back cover of the machine, DO NOT touch the shaded parts shown in the illustrations.
To prevent injuries, be careful not to put your hands on the edge of the machine under the document cover as shown in
the illustration.
To prevent injuries, be careful not to put your fingers in the areas shown in the illustrations.
When you move the machine, grasp the side hand holds that are under the scanner.
IMPORTANT
The fuser unit is marked with a Caution label. Please DO NOT remove or damage the label.
● Important safety instructions
1 Read all of these instructions.
2 Save them for later reference.
3 Follow all warnings and instructions marked on the product.
4 Unplug this product from the wall socket before cleaning inside of the machine. DO NOT use liquid or aerosol cleaners.
Use a dry lint-free soft cloth for cleaning.
5 DO NOT place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the
product.
6 Slots and openings in the casing at the back or bottom are provided for ventilation. To ensure reliable operation of the
product and to protect it from overheating, these openings must not be blocked or covered. The openings should never
be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near
or over a radiator or heater. This product should never be placed in a built-in installation unless adequate ventilation is
provided.
7 This product should be connected to an AC power source within the range indicated on the rating label. DO NOT connect
it to a DC power source or inverter. If you are not sure, contact a qualified electrician.
8 This product is equipped with a 3-wire grounded plug. This plug will only fit into a grounded power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet, call your electrician to replace your obsolete outlet. DO NOT
defeat the purpose of the grounded plug.
9 Use only the power cord supplied with this machine.
10 DO NOT allow anything to rest on the power cord. DO NOT place this product where people can walk on the cord.
11 If an extension cord is used with this product, make sure that the total ampere ratings on the products plugged into the
extension cord DO NOT exceed the extension cord ampere rating. Also, make sure that the total of all products plugged
into the AC power outlet does not exceed 15 amperes (US only).
12 Use the product in a well-ventilated area.
13 The power cord, including extensions, should be no longer than 16.5 feet (5 metres).
DO NOT share the same power circuit with other high powered appliances, such as an air conditioner, copier, shredder,
and so on. If you cannot avoid using the printer with these appliances, we recommend that you use a voltage transformer
or a high-frequency noise filter.
Use a voltage regulator if the power source is not stable.
14 DO NOT place anything in front of the machine that will block received faxes. DO NOT place anything in the path of
received faxes.
15 Wait until pages have exited the machine before picking them up.
16 Never push objects of any kind into this product through cabinet slots, since they may touch dangerous voltage points or
short out parts resulting in the risk of fire or electric shock. Never spill liquid of any kind on the product. DO NOT attempt
to service this product yourself because opening or removing covers may expose you to dangerous voltage points and
other risks and may void your warranty. Refer all servicing to a KONICA MINOLTA Authorized Service Center.
17 Unplug this product from the power socket and refer all servicing to our Authorized Service Personnel under the following
conditions:
„
When the power cord is damaged or frayed.
„ If liquid has been spilled into the product.
„ If the product has been exposed to rain or water.
„ If the product does not operate normally when the operating instructions are followed. Adjust only those controls that
are covered by the operating instructions. Incorrect adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
„ If the product has been dropped or the casing has been damaged.
„ If the product exhibits a distinct change in performance, indicating a need for service.
18 To protect your product against power surges, we recommend the use of a power protection device (Surge Protector).