Masterbuilt Propane Turkey Fryer with Turkey Tap (20020507) - Manual (Page 15)

9
APAGADO
APAGADO
ENCENDIDO
ENCENDIDO
CONEXIÓN DE TIPO 1
AL TANQUE DE GAS
EN SENTIDO
DE LAS
AGUJAS DEL
RELOJ
EN SENTIDO
DE LAS
AGUJAS DEL
RELOJ
EN SENTIDO
CONTRARIO
A LAS
AGUJAS DEL
RELOJ
EN SENTIDO
CONTRARIO
A LAS
AGUJAS DEL
RELOJ
Inspeccione la manguera antes de
cada uso.
Si muestra señales de desgaste, cortes
o fugas, cambie la manguera y el
regulador con la pieza 903070006.
OPERACIONES DE LA VÁLVULA DE CONTROL DEL REGULADOR
CONEXIÓN DEL REGULADOR A LA VÁLVULA DEL TANQUE
CONTROL DEL REGULADOR
AJUSTE DE LA LLAMA
La válvula de control del regulador se
usa para regular la llama del
quemador. El girar la perilla de control
en el sentido de las agujas del reloj
permite aumentar lentamente la llama
del quemador, y en el sentido
contrario a las agujas del reloj
permite reducirlas hasta apagar el
quemador.
Ajuste el regulador de aire al quemador,
hasta que la llama del quemador sea lo más
azul posible
El gancho del regulador se usa para mantener el
regulador separado de la tierra cuando no está
conectado al tanque.
Fíjelo a la unidad, como se ilustra
Los reguladores de tipo 1 tienen un gancho,
como se ilustra.
AMARILLA
AZUL
LLAMA
CORRECTA
LLAMA
INCORRECTA
Regulator Control Valve
Soapy Water Test Warning and Procedures
• The Soapy Water Test must be performed each time gas cylinder is connected to appliance or
each time the appliance is used.
• The Soapy Water Test must be performed outdoors in a well-ventilated area.
• When performing the Soapy Water Test, always keep fryer away from open flames, sparks, or lit
cigarettes.
• This Outdoor Gas Turkey Fryer is designed to operate with propane gas only. This product will not
operate with natural gas.
• Never use an open flame to test for gas leaks.
• Always remove any cookware from turkey fryer stand when performing the Soapy Water Test.
PROCEDURE:
1.Remove any cookware from your fryer stand.
2. Turn regulator to OFF position, and turn the gas cylinder valve to the OFF
position.
3. Prepare your soapy water solution by combining (1) one part dish washing
liquid with (3) three parts water to test for the possibility of any gas leaks in the
hose or connections to regulator and the regulator connection to gas cylinder.
Apply soapy water solution to the gas cylinder valve, regulator and along the
hose to the burner.
4. Turn gas cylinder valve ON (regulator control valve should be in the OFF
position) and observe gas cylinder valve for bubbles. DO NOT LEAVE GAS ON
FOR MORE THAN 12 SECONDS. If bubbles appear, stop, turn gas cylinder
OFF, and retighten the fitting. Repeat test.
5. When the gas cylinder has been tested, follow timer operation instructions on
page 10. DO NOT LIGHT BURNER. Open the regulator control valve one full
turn and check for bubbles at regulator control valve, along the entire length of
hose and at the connection to the burner . DO NOT LEAVE GAS ON FOR
MORE THAN 12 SECONDS. If soapy mixture starts bubbling, gas is leaking
through the connection or hose. Turn the regulator valve OFF and then the gas
cylinder OFF and retighten the connection that is leaking gas. After test is
complete, and there are no leaks, wait a minimum of 5 minutes for gas fumes
to diminish before lighting fryer.
6.Once testing is complete, press power button on timer to stop gas flow.
DURING ANY PORTION OF THE SOAPY WATER TEST, IF BUBBLES CONTINUE TO
APPEAR, STOP, DO NOT USE THE APPLIANCE AND CONTACT YOUR LOCAL PROPANE
DEALER OR MASTERBUILT AT 1-800-489-1581.
NOTE: USE A 20 LB (9KG) CYLINDER WITH A PROTECTIVE COLLAR WITH THIS
APPLIANCE. ONLY CYLINDERS MARKED “PROPANE” MUST BE USED.
Bubbles in Soapy Water Test
Burner, Hose and orifice
Connection
Burner, Hose, Regulator and
Cylinder Valve
14