Aqua Bath IS3639SH - Manual (Page 2)

12/08
AQUA BATH COMPANY INC.921 Cherokee Ave.Nashville, TN 372071-800-232-2284Fax (615) 227-9446
 www.aquabath.com 
ACCESSIBLE SERIES
• Model
IS3639SH-L valve on left.
• Model IS3639SH-R valve on right.
• Bath units designed for hospitals, nursing homes, rehabilitation
centers, hotels, motels and residential applications.
• Acrylic one-piece molded construction simplifies installation.
• Inside dimensions: 36” W x 39” D x 78” H.
• Can be furnished complete with valve, hand held shower set,
curtain and hooks.
• 5” threshold.
• Two 24” vertical grab bars.
• Vacuum-formed from .1875” one-piece sanitary grade acrylic.
• Manufacturing Tolerance Of (±1/4”) Due To The Nature
Of The Materials Used.
Acrylic Corner Shower Stall
The shower enclosure shall be Aqua Bath model IS3639SH acrylic and be molded from a single sheet so as not to have any
joints or seams, shall meet ANSI Z124.2. Unit shall have a backside flame spread of less than 30 (Class B).
Shall be designed to be NAHB LISTED. The enclosure shall have inside dimensions of 36” W x 39” D x 78” H and outside
dimensions of 43½” W x 39½” D x 84” H. A soap tray is molded 47” above the shower floor on the back corner.
The approximate weight of the unit shall be 235lbs.
The unit shall be formed with a patented recessed trench system so as to direct water to the center drain.
Standard Accessories:
1) Two 24” x 1½” diameter vertical grab bars, fabricated from 18 gauge stainless steel with 1½” safety statute clearance,
mounted with stainless steel bolts and secured from the rear with 3” x 3” x 11 gauge metal mounting plates.
2) 1” diameter, 18 gauge stainless steel curtain rod. After grab bars and curtain rod have been factory installed, they will be
sealed from the backside making the unit completely waterproof.
3) Ribbed bottom for slip resistance (standard).
Available Accessories:
1) Factory installed fold-up seat.
2) Hand held shower set (includes 60” flex hose, swivel connector, brass nipple, lock nut, wall outlet and vacuum breaker).
3) 24” slide bar, 30” slide bar or two (2) wall brackets installed on valve wall for use with hand held shower set.
Note: The determination of the use of slide bar or wall brackets to be installed in the unit is based upon the valve package
chosen by the specifier for use in the unit. Aqua Bath recommends the use of a slide bar as an accessory in the unit rather
than the use of a glide bar / glide rail.
4) Pressure balance or thermostatic control valve. 5) Shower curtain - antibacterial, with hooks.
6) Weighted shower curtain (patented), antibacterial, with hooks. 7) Seat belt (for the fold-up seat only).
8) Dome light (factory drilled only, must be field installed and light shipped separately from unit).
9) ASTM F462 non-slip bottom. (*) When the ASTM F462 bottom is specified with the center drain location,
it will re-configure the trench drain system. A signed off approval is required for the bottom re-configuration.
Modifications: Received and / or approved by:
Name:______________________________
Company:___________________________
Title:_______________________________
Phone:______________________________
Date:_______________________________
The IS3639SH is NOT ADA compliant.
Please see Aqua Bath’s full line of ADA
compliant shower and tub/shower units.
Please check with your local city and
state for code compliancy. Aqua Bath
accepts no responsibility for final code
compliance.
For additional information, call the
Aqua Bath Customer Service
Department At 1-800-232-2284