Aqua Bath C6530BF 2 PSY VP (valve pkg) - Manual (Page 2)

02/09
AQUA BATH COMPANY INC.921 Cherokee Ave.Nashville, TN 372071-800-232-2284Fax (615) 227-9446
 www.aquabath.com 
CARE SERIES
•
Model C6530BF 2” PSY VP-L valve on left.
• Model C6530BF 2” PSY VP-R valve on right.
• Bath units designed for hospitals, nursing homes, rehabilitation
centers, hotels, motels and residential applications.
• Shall accommodate a wheelchair or a shower chair.
• Meets ANSI A117.1, ADA Guidelines and other standards
for accessibility
• Acrylic one-piece molded construction simplifies installation.
• Inside dimensions: 60” W x 30” D x 78” H.
• Includes stainless steel grab bars (tamper proof) with mounting
plates and curtain track with pop out carriers and hooks.
• 2” threshold for pit detail installation.
• 3/4” threshold for top of slab installation or pit detail installation.
• Vacuum-formed from .1875” one-piece sanitary grade acrylic.
For additional information, call the
Aqua Bath Customer Service
Department At 1-800-232-2284
Please check with your local city and
state for code compliancy. Aqua Bath's
advertised ADA compliant units are
based on our interpretation of the
Americans with Disabilities Act 1991
Guidelines. Field alterations or improper
installation could take the units out of
compliance. Aqua Bath accepts no
responsibility for final code compliance.
• Manufacturing Tolerance Of (±1/4”) Due To The Nature
Of The Materials Used.
Roll-In Shower Stall
The shower enclosure shall be Aqua Bath model C6530BF 2” PSY VP acrylic and be molded from a single sheet so as not to
have any joints or seams, shall meet ANSI Z124.2. Shall meet ADA guidelines and other standards for accessibility. Unit shall
have a backside flame spread of less than 30 (Class B). Shall be designed to be ADA COMPLIANT and NAHB LISTED.
The enclosure shall have inside dimensions of 60” W x 30” D x 78” H and outside dimensions of 65” W x 31” D x 84” H.
The approximate weight of the unit shall be 275lbs. The unit shall be formed with a patented recessed trench system so as to
direct water to the center drain. ADA states that the threshold must be flush with the finished floor. Because of the
threshold height, the unit must be installed in a pit to comply with ADA.
Standard Accessories:
1) One 48” x 1½” diameter (back wall) and two 22” x 1½” diameter (one on each side wall) 18 gauge stainless steel grab bars
with a closure plate welded to the bottom of the bar (full length) making the bar tamper proof. Grab bars will be mounted with
stainless steel bolts and secured from the rear with 3” x 3” x 11 gauge metal mounting plates. After the grab bars have been
factory installed, they will be sealed from the backside making the unit waterproof.
2) White PVC curtain track with tamper proof screws and pop out carriers and hooks (designed to pop out at 40lbs of weight).
3) Self contained and ADA Compliant push button control conical shower head system with removable access panel for
plumbing access and tamper proof screws.
4) Ribbed bottom for slip resistance (standard).
5) Self-caulking brass drain (tamper proof, fits 2” pipe) with stainless steel strainer and drain is to be field installed.
Available Accessories:
1) Shower curtain - antibacterial, with hooks.
2) Tamper proof dome light (factory drilled only, must be field installed and light shipped separately from unit).
3) ASTM F462 non-slip bottom. (*) When the ASTM F462 bottom is specified with the center drain location,
it will re-configure the trench drain system. A signed off approval is required for the bottom re-configuration.
Modifications: Received and / or approved by:
Name:______________________________
Company:___________________________
Title:_______________________________
Phone:______________________________
Date:_______________________________