Muxlab HDMI 4x8 Matrix Switch, HDBT - Manual (Page 58)

© MuxLab Inc. HDMI 4x8 Matrix Switch, HDBT, PoE Installation Guide
Page 58
6. POST Commands
POST commands will always return 1 of 5 HTTP headers:
HTTP 201Created Command was successful
HTTP 400 Bad Request Received argument was malformed
HTTP 403 Forbidden User does not have sufficient privileges
HTTP 404 Not Found URL is incorrect
HTTP 501 Not Implemented URL does not support receiving POST data
URL Argument
/var/conn.json Array of connections.
(Same as GET above)
Example: [0,1,2,3,2,1,3,4]
/var/pre1.json
/var/pre2.json
/var/pre3.json
/var/pre4.json
/var/pre5.json
/var/pre6.json
/var/pre7.json
/var/pre8.json Array of connections for a preset
(Same as GET above)
Example: [0,1,2,3,2,1,3,4]
/var/boxname.json Array of a single string.
Contains the name of the box, limited to 20 characters
Example: [“Classroom B Matrix”]
/var/sources.json Array of 4 strings.
Contains the names of all 4 input ports.
Example: [“Cable Box”, “Satellite Receiver”, “Demo Reel”, …]
/var/displays.json Array of 8 strings.
Contains the names of all 4 output ports.
Example: [“Conference Room”, “Cafeteria”, …]
/var/presetnames.json Array of 8 strings.
Contains the names of all 8 presets to be set
Example: [“Preset 1”, “Preset 2”, “week end”, …]
/var/auth.json Array of 2 strings.
Contains a single digit string representing the user level requested, and a second string representing the password.
Example: [“2”, “myAdminPassword”]
/var/serial.json Array of 4 integers.
Set the following serial port settings: baud rate, data bits(7 or 8), parity (0=>Even; 1=>Odd; 4=>None) ,stop bits
(0=>1 stop bit; 2=>2 stop bits)
Example: [9600,8,4,0]
/var/ip.json Array of 4 integers.
Set the IP address
Example: [10,0,101,96]
WARNING! This request will actually take effect after the DHCP request will be sent
/var/netmask.json Array of 4 integers.
Set the mask address
Example: [255,255,0,0]
WARNING! This request will actually take effect after the DHCP request will be sent
/var/router.json Array of 4 integers.
Set the gateway address
Example: [10,0,1,1]
WARNING! This request will actually take effect after the DHCP request will be sent
/var/dhcp.json Array of a single integer.
Set the DHCP state ON ([1]) or OFF ([0])
Example: [1]
/var/tempalarms.json Array of 2 integers.
Set the Min. and Max. temperature of the unit before an alarm is raised
Example: [5,70]
/var/alarmflags.json Array of 8 integers.
Set the alarm configuration: beep, email, serial feedback, (the last 5 integer are not used)
Example: [1,0,1,0,0,0,0,0]
var/pass_admin.json Array of 2 strings.
Set the web administrator password
Example: [“old admin password”, “new admin password”]
var/senddata Hexadecimal data string to send in the request formatted as follow:
Example: [“03060A010203040506070809A0”]
03 is the port number (here it is port # 3)
06 is the baud rate code:
 For 9600 the code is 06
 For 19200 the code is 08
 For 38400 the code is 09
 For 57600 the code is 0B
 For 115200 the code is 0C
0A is the data length that follows (max value 0x28 bytes.)
01A203040506070809A0 is the data in hexadecimal (0x01, 0xA2, 0x03,…)