SawStop Out-Feed Table - Manual (Page 3)

Installing Your Out-Feed Table
Moving b elts and par ts
can pinch , cut or cr ush.
Do not op erate with
belt guar d open.
5. Align the three holes in the rear rail
with the three holes in the out-feed
table mounting bracket and thread
the three mounting screws through
the rear rail and into the mounting
bracket (see Fig. 5). Thread the
screws into the mounting bracket
enough so they engage the bracket,
but do not tighten them. They need
to remain loose so you can align the
out-feed table to the saw.
Fig. 5
Fig. 8 Fig. 7
Saw Stop , t he Saw Stop blad e log o, and the
con figu rati on of t his prod uct are eit her reg ister ed
trad em ark s o r t rad em ark s o f S awS top , LL C.
Soft war e c opy righ t 200 3-2 006 by SawS top , LL C.
All righ ts r eser ved. Pro tec ted by one or m ore of
the fol low ing U .S. pat ent s 68 1398 3, 682 698 8,
685 7345 , 68 774 10, 688 044 0, 6 9208 14, 6945 148 ,
694 5149 , 69 5760 1, 69 940 04, 69 970 90, 70 005 14,
702 497 5, 70 554 17, 707 703 9, 7 0988 00, 7100 483 ,
713 732 6, 71 7187 9, 71 979 69, 72 103 83, 72 257 12,
722 8772 , 72 3185 6 an d T aiw an paten t 14 346 6.
Add itiona l U. S. an d fo reign pat ent s pe ndi ng.
! WA RNI NG
Do not rem ove the dus t shr oud be cau se
the blad e wi ll be expo sed . If you con tact the
blad e un der the tabl e, th e bl ade may retr act
towa rd you and ca use a s ever e i njur y.
6. Align the out-feed table to the saw table by turning the adjustment screws in the mounting bracket. The heads
of the adjustment screws will contact the top surface of the rear rail when the out-feed table is in place on the
saw, so turning the adjustment screws will raise or lower the out-feed table. Back the adjustment screws out of
the mounting bracket to raise the out-feed table, and thread the adjustment screws into the mounting bracket
to lower the out-feed table. Use a 13 mm wrench to set the height of each of the adjustment screws. Use a
straight-edge to align the top surface of the out-feed table to the top surface of the saw. Once the top surfaces
are aligned, tighten the three mounting screws using a 13 mm wrench. As you tighten the mounting screws you
may need to further adjust the position of the adjustment screws to keep the top surfaces aligned.
7. Level the out-feed table by turning the foot
on the bottom of each support leg until the
top surface of the out-feed table is level
with the top surface of the saw (see Fig. 7).
Once the top surfaces are level, fully tighten
the hex nut against the bottom of the legs
using a 13 mm wrench (see Fig. 8).
Fig. 6
Made in Taiwan SawStop, LLC www.sawstop.com TCP
10¨ Contractor Saw
SawStop ®
Model No. CNS 175 Serial No. C074012345
Electrical / Electricidad / Électricité
115/230 Volts, 60 Hz 15/7.5 Amps 1 Phase
1.75 HP 3500 RPM
® c US 175370
Moving b elts and par ts
can pinch, cut or cr ush.
Do not op erate wit h
belt guar d open.
adjust the position of the foot
until the out-feed table is
level and tighten the hex nut
straight-edge
adjustment
screw
mounting
screw
mounting
screws
straight-edge
Congratulations,
your out-feed table is now
installed and ready for use.