beautypg.com

Custom Brackets Tilt Head AS User Manual

Attaching the tilt head as to a monopod, Indexing the quick release to accept a camera, Innovative camera supports

background image

Lens lock knob

(press in and rotate

clockwise to tighten)

Tilt lock knob

(rotate counter-clockwise

to tighten)

Tilt drag knob

(rotate clockwise

to tighten)

T i l t H e a d A S I N S T R U C T I O N S

phone 446-446-0819

Toll Free 800-530-2289

website: www.custombrackets.com

email: [email protected]

32 Alpha Park

Cleveland, Ohio 44143

Made in USA

Quick release

reference lines

Lens plate

reference lines

Lens lock knob

Attach lens with lens plate

by loosening lens lock knob

completely, then place lens

plate into quick release. Tighten

lens lock knob completely, then

loosen 1/2 turn. Slide lens

forward or backward to balance,

then retighten lens lock knob.

If you have a replacement lens

foot, use the same procedure

above.

Install screw(s) into lens plate at the labeled

ends. The screw(s) and

/

or plate may be

damaged if installed incorrectly. Some

lenses will require both screws be in one

slot.
The “D” screw has a fold out clip for

hand tightening. A screwdriver slot is also

included on the screw.
Do not insert any object as leverage into the

“D” clip as it will damage screw and void

warranty.

A lens may have 1/4” and

/

or 3/8” threaded

holes. (1) 3/8” and (2) 1/4” screws are

included with each lens plate. It is important

to use the correct size.

Mounting holes

Attaching lens plate to lens

Attaching lens to Tilt Head AS

Tilt Head AS Features

Front View

Arca Swiss style

quick release

Innovative Camera Supports

Attach the Tilt Head AS to the monopod’s ⅜”-16 mounting stud and tighten until firmly attached.

* * * * * Caution * * * * *

If you are using a monopod with a ¼”-20 mounting stud, you will need to purchase a ⅜” to ¼” reducer

bushing and install it in bottom of the Tilt Head’s base.

Attaching the Tilt Head AS to a monopod

For a period of five (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any

defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any

modifications made by the customer. Excessive force unscrewing knobs will void warranty. Warranty service is

available by returning the Tilt Head AS (shipping prepaid) to Custom Brackets. All returns must include a return

authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem, and a copy of

the sales receipt.

USA 5 Year Warranty

Repair service is available by returning the Tilt Head AS (shipping prepaid) to Custom Brackets. All returns

must include a return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the

problem, and a copy of the sales receipt. A repair cost will be issued and must be approved prior to any

repairs. Shipping charges are the responsibility of the customer.

Repair

The Tilt Head AS is designed completely maintenance-free.

Maintenance

For a period of five (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any

defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any

modifications made by the customer. Excessive force unscrewing knobs will void warranty. Limitation to the

warranty - after year one shipping charges are not covered. Warranty service is available by returning the Tilt

Head AS (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number

(email [email protected] to obtain), letter explaining the problem, and a copy of the sales receipt.

International 5 Year Limited Warranty

The Tilt Head AS has many unique features. It is constructed from anodized aluminum for a lightweight

and scratch-resistent finish. The tilt head has separate lock and drag knobs for better control. All knobs

are captive to prevent loss. All of the fasteners are stainless steel to resist corrosion and black oxide for

appearance.

Tilt Head AS Features

Indexing the quick release to accept a camera

Using the supplied allen wrench (3/16”), remove

screw from the top of the quick release, then lift

the quick release off the Tilt Head.
Align quick release far right image (Camera Setup)

and align pins using pin holes #1 & #2 (see below)

in top of the tilt head. Once in place, install screw

into the top of the quick release of the Tilt Head.

For Long Lens Setup, use pin holes #2 & #3.

Long Lens

Setup

Camera

Setup

Top view of Tilt Head

(quick release removed)

Hole #2

Hole #3

Hole #1