Alpine PKG-RSE2 - Manual (Page 24)

22
-EN
2 Use the number keys “0” to “9” to input the 4-digit
password, then press ENTER.
PASSWORD ✽ ✽ ✽ ✽
Input numbers are displayed as “✽.“
The default password is 1111 upon shipment from the factory.
The restriction level (PARENTAL LEVEL) input display appears.
• Can be erased one digit at a time each time CLR is pressed. Press
and hold CLR for at least 2 seconds to delete all digits.
• Press RETURN to return to the previous screen.
• If the password is wrong, the unit displays “PASSWORD ERROR”
for 5 seconds. It then returns to the password input display where
the password may be reentered.
3 Press , , or to select the rating level (1 to 8), then
press ENTER.
Select “OFF” to cancel the parental lock or if you do not want
to set a rating level.
The lower the number, the higher the rating level.
• Press RETURN to return to the previous display.
4 Press DVD SETUP.
The settings are stored and the setup mode is deactivated.
• If you want to change the password, select “CHANGE
PASSWORD,” then input the new password (4 digits).
• Write down the password on a piece of paper and store the piece of
paper somewhere in case you forget it.
• On unrated DVDs, playback will not be restricted even if the rating
level is set.
• Once set, this rating level remains in memory until changed. To
enable the play of discs of higher rating levels or to cancel the
parental lock, the setting must be changed.
• Not all DVDs provide a Parental Lock feature. If you are unsure
about a DVD, play it first to confirm. Do not leave DVDs
accessible to young children for whom you deem them
inappropriate.
Tips
• Changing the rating level temporarily
Some discs may request that you change the rating level set
in the default settings during playback. In this case, the
message appears on the monitor screen “PARENTAL
LEVEL CHANGE OK?”
• To change parental level and play, press ENTER.
The password input mode is displayed. Input the 4-digit
password in “Setting the Rating Level (Parental Lock)” you
set, then press ENTER.
• To play without changing the parental level, press ■.
(When ■ is pressed, playback will be at the parental level
set with “Setting the Rating Level (Parental Lock).”)
Setting the Digital Output
Digital output is not available on this Built-in DCD 10.2 inch
overhead monitor, PKG-RSE2. It will not affect the monitor, if you
change the setting.
16 : 9 WIDE
Select this when connected
to a wide screen TV. This
is selected upon shipment
from the factory.
4 : 3 LB (LETTER BOX)
Select this when connected to a
conventional 4 : 3 size (normal TV
aspect ratio) monitor. There may
be black bands visible at the top
and bottom of the screen (when
playing a 16 : 9 size movie). The
width of these stripes will depend
upon the original aspect ratio of the theatre release of the
movie.
4 : 3 PS (PAN- SCAN)
Select this when connected
to a conventional 4 : 3 size
monitor. The picture will fill
the entire TV screen.
However, due to the
mismatch in aspect ratio,
parts of the movie at the
extreme left and right sides will not be visible (when playing a
16 : 9 size movie).
Setting the Country Code
Set the country number of which you want to set the rating level
(Parental lock).
Setting item: COUNTRY CODE
Setting contents: CODE
1 Press ▲ or ▼ to select “COUNTRY CODE,” then press
ENTER.
“COUNTRY CODE” will be reset.
COUNTRY CODE - - - -
2 Use the number keys “0” to “9” to input the 4-digit
country code, then press ENTER.
Example: United States “8583” is input
COUNTRY CODE 8 5 8 3
• If the input code is wrong, the unit returns to the country code
input display, after display “CODE ERROR” for 5 seconds.
• For the country codes, refer to “List of Country Codes” (Pages 30
and 31).
• Can be erased one digit at a time each time CLR is pressed. Press
and hold CLR for at least 2 seconds to delete all digits.
• Press RETURN to return to the previous screen.
Setting the Rating Level (Parental Lock)
Use this function to restrict the viewing of movies to children of
appropriate age levels only.
Setting item: PARENTAL
Setting contents: PASSWORD
1 Press ▲ or ▼ to select “PARENTAL,” then press ENTER.
The password input mode is activated.