Nilfisk-ALTO 580 P - Manual (Page 19)

USER MANUAL ENGLISH
146 2603 000(1)2005-03 A FLOORTEC R 580 P 17
PETROL FILTER CLEANING
1. Drive the machine on a level ground.
2. Engage the parking brake using the pedal and the
lever (22 and 15, Fig. B).
3. Turn the ignition key (15, Fig. B) to “0” position.
4. Unscrew the screws (26, Fig. V) and disengage the
retainers (27) to remove the left side bulkhead (25).
5. Unscrew the screws (7, Fig. AE) and remove the
engine air conveyor (8).
6. Clean the petrol filter (10, Fig. AS) as indicated in the
Petrol Engine Manual.
7. Carry out steps from 1 to 5 in the reverse order.
ENGINE AIR PRE-FILTER CLEANING AND
ENGINE AIR FILTER CARTRIDGE
MAINTENANCE
1. Drive the machine on a level ground.
2. Engage the parking brake using the pedal and the
lever (22 and 15, Fig. B).
3. Turn the ignition key (14, Fig. B) to “0” position.
4. Unscrew the screws (26, Fig. V) and disengage the
retainers (27) to remove the left side bulkhead (25).
5. Remove the pin (1, Fig. AE) from its seat (9) and
insert it in the hole (2) of the lever (5).
6. Lower the main broom by means of the lever (20, Fig.
B) to disengage the rod (3, Fig. AE).
7. Disengage and remove the pin (4, Fig. AE), then
disconnect the tie rod (3) from the lever (5).
8. Clean the engine air pre-filter and/or perform the
petrol engine filter cartridge (6, Fig. AE), maintenance
as indicated in the Petrol Engine Manual.
9. Carry out steps from 1 to 7 in the reverse order.
SPARK SCREEN CLEANING
1. Drive the machine on a level ground.
2. Engage the parking brake using the pedal and the
lever (22 and 15, Fig. B).
3. Turn the ignition key (14, Fig. B) to “0” position.
4. Unscrew the screws (26, Fig. V) and disengage the
retainers (27) to remove the left side bulkhead (25).
5. Unscrew the fixing screws and remove the engine
exhaust system end (31, Fig. V).
6. Clean the spark screen as indicated in the Petrol
Engine Manual.
7. Carry out steps from 1 to 5 in the reverse order.
ENGINE SPARK PLUG
CLEANING/REPLACEMENT
1. Drive the machine on a level ground.
2. Engage the parking brake using the pedal and the
lever (22 and 15, Fig. B).
3. Turn the ignition key (14, Fig. B) to “0” position.
4. Open the hood (1, Fig. V).
5. Unscrew the screws (23, Fig. V) and remove the
engine guard (22) by disengaging the retainers (24).
6. Clean/replace the spark plug (29, Fig. V) as indicated
in the Petrol Engine Manual.
7. Carry out steps from 1 to 5 in the reverse order.
ENGINE COOLING SYSTEM CLEANING
1. Drive the machine on a level ground.
2. Engage the parking brake using the pedal and the
lever (22 and 15, Fig. B).
3. Turn the ignition key (14, Fig. B) to “0” position.
4. Unscrew the screws (26, Fig. V) and disengage the
retainers (27) to remove the left side bulkhead (25).
5. Open the hood (1, Fig. V).
6. Unscrew the screws (23, Fig. V) and remove the
engine guard (22) by disengaging the retainers (24).
7. Unscrew the screws (7, Fig. AE) and remove the
conveyor (8).
8. Clean the engine cooling system (11, Fig. AE) as
indicated in the Petrol Engine Manual.
9. Carry out steps from 1 to 7 in the reverse order.