Ferguson AV-660 - Manual (Page 14)

13
REMOTE CONTROL FUNCTION
NO. & NAME DESCRIPTION NO. & NAME DESCRIPTION
1.
POWER
ON/STANDBY Press this button to turn this unit on or
Into standby mode. 18.
NUMERIC
BUTTONS These buttons are used to select a preset
channel during the tuner mode.
2.
SURR MODE Press this button to choose one of the
following surround modes: THEATER,
HALL, PASSTHRU, MOVIE, MUSIC
and ROOM. 19.
TUNING +/- Tuner frequency up and down.
3.
DIMMER Press this button to set the brightness of
the front display. 20.
AUTO /MANUAL This button is used to select AUTO or
MANUAL tuning in AM and FM mode.
Press once to set to AUTO again for
MANUAL.
4.
DOLBY DIGITAL When play 5.1 CH source, and while you
are enjoying Stereo, press this button to
playback source in DOLBY DIGITAL. 21.
MEMORY Press it to store the broadcast station as a
preset.
5.
DTS
When play 5.1 CH source, and while you
are enjoying Stereo, press this button to
playback source in DTS. 22.
PTY In FM state, press this button, the current
program type appears on the display, using
TUNING +/- to select the program type
you desire.
6.
PRO LOGIC IIx When receiving Analog/digital /PCM
signal or 2CH Pro Logic, turn on this
button then the playing is under analog
5.1CH state. 23.
CH SELECT
Select channels by pushing this button,
then use VOL. +/- buttons to balance
speakers.
7.
DTS NEO: 6 When the input signal is PCM, pressing
this button, you will get DTS NEO 6
MUSIC or DTS NEO 6 CINEMA.
26.
LFE TRIM Under the Pro Logic 5.1CH or DTS 5.1CH
mode, press this button and adjust the
volume to set the Low Frequency output
level
8.
SURR BACK Push this button to turn on or off the
surround back output. And when surround
back output is off, the DTS NEO:6 is
activated. 27.
DYNAMIC Press this button repeatedly to reach your
desired compression dynamic range.
9.
SUB ON/OFF Press this button to turn on/off the output
of subwoofer. 28.
TEST TONE To balance speakers in Dolby Digital or
Dolby Pro Logic mode.
10.
DIRECT IN Press this button to select the 6.1
analogue input. 29.
DISPLAY Press this button to display the state of
input source. And when listening to the
FM broadcasting with RDS, press this
button to show PS, PTY, RT and RT.
11.
INPUT MODE To select input modes: ANA, OPT, and
COAX when using digital in. 30.
STEREO With this unit in STEREO mode, only
Front Left & Front Right speakers and
Woofer have output.
12.
MUTE Press this button to mute the sound, push
again to cancel the mute function. 31.
SPK SETUP Under PRO LOGIC II or Digital state, it
can change the desired Speaker Setting
shown on the display.
13/24.
VOL. +/- Press these buttons to decrease or increase
the volume. 32.
+ / - These buttons are used for SPK SETUP
and DELAY TIME, Treble and Bass
adjustment.
14.
APS Allocates and memorizes radio stations
automatically. 33.
DELAY Press this button to set the delay time for
the Dolby digital/Dolby Pro Logic modes.
15/25.
SOURCE SEL Press this button to select source upward
or downward. 34.
TREBLE Press this button for Treble adjustment,
then press +/- key to adjust the level.
(Note: In Pro Logic II, Surround and
Digital 5.1 mode, no function.)
16.
ST/MONO Press this button to alternate between
Stereo and Mono mode when listen to FM
broadcast. 35.
BASS Press this button for Bass adjustment, then
press +/- key to adjust the level. (Note: In
Pro Logic II, Surround and Digital 5.1
mode, no function.)
17.
BAND Press this button to alternate between FM
and AM.