Allied Telesis AT-WDM02 - Manual (Page 2)

6. Using a flathead screwdriver, secure the module to the AT-WD1008
chassis by tightening the captive screw.
7. Attach the MiniDIN8 connector on the management cable to the
RS-232 port on the management module. Attach the other end
of the cable to a terminal or a personal computer with a terminal
emulator program.
8. To manage the multiplexer from a remote management station,
connect a Category 3 or better twisted pair cable with an RJ-45
connector to the 10Base-T port on the management module.
Connect the other end of the twisted pair cable to a half-duplex
10 Mbps or 10/100 Mbps port on an Ethernet hub or switch.
LNK TST
TX
RX
LNK TST
TX
RX
CH 3
TX
RX
RX
TX
CH 4
SNMP MODULE
WEST
EAST
TX
RX
RX
TX
CH 5
TX
RX
RX
CH
POWER
SUPPL
Y A
POWER
SUPPL
Y B
WEST
EAST
NORMAL
LNK TST
10BASE
-T PORT
RS-232
TERMIN
AL COL
RX
LNK
STATUS
POWER
RESET
LNK TST
TX
RX
LNK TST
TX
RX
CH 3
TX
RX
RX
TX
CH 4
SNMP
MODULE
WEST
EAST
TX
RX
RX
TX
CH 5
TX
RX
RX
CH
POWER
SUPPL
Y A
POWER
SUPPL
Y B
WEST
EAST
NORMAL
LNK TST
10BASE-T PORT
RS-232
TERMINAL
COL
RX
LNK
STATUS
POW ER
RESET
LNK TST
TX
RX
LNK TST
TX
RX
CH 3
TX
RX
RX
TX
CH 4
SNMP
MODULE
WEST
EAST
TX
RX
RX
TX
CH 5
TX
RX
RX
CH
POWER
SUPPL
Y A
POWER
SUPPL
Y B
WEST
EAST
NORMA
L
LNK TS
T
10BASE-T PORT
RS-232
TERMINAL
COL
RX
LNK
STATUS
POWER
RESET
9. If you are installing the AT-WD1008 Multiplexer for the first time, refer
to the AT-WD1008 Installation Guide for instructions on how to
complete the installation. Otherwise, power ON the AT-WD1008
Multiplexer. If the multiplexer contains an RPS unit, power ON the RPS
unit as well.
This completes the installation procedure for the management module.
For instructions on how to establish a management session, refer to the
AT-S47 Management Software User’s Guide, available from the Allied
Telesyn web site.
Reset Button
On the front panel of the management module is a Reset button. Pressing
the button resets the AT-WDM02 Management Module. Resetting the
management module does not interrupt the flow of data traffic through
the multiplexer.
Management Module LEDs
Note
For information on the AT-WD1008 LEDs, refer to the AT-WD1008
Installation Guide.
LED Color Description
COL Flashing
Yellow Collisions are occurring between the
10Base-T port on the management
module and the Ethernet hub or switch
to which the port is connected.
RX Flashing
Green The 10Base-T port is receiving packets.
LNK Solid Green A valid link has been detected on the
RJ-45 port.
STATUS Solid Green The module is functioning normally.
Solid Amber The module is performing a self-test.
Flashing
Amber The module is downloading firmware
from a host PC.
Solid Red The module or management software is
malfunctioning.
POWER Solid Green The management module is receiving
power.
Port Pinouts
RJ-45 Port Pinouts
RS232 Port Pinouts
Electrical Safety and Emission Statement
Standards: This product meets the following standards when installed in compliant host equipment.
Emission FCC Class A, EN55022 Class A, VCCI Class A, EN6100-3-2, EN6100-3-3
WARNING: In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
Immunity EN55024
Electrical Safety UL60950 (cULus), EN60950 (TUV)
Copyright  2003 Allied Telesyn, Inc. All rights reserved.
No part of this publication may be reproduced without prior written permission from Allied Telesyn Inc.
MDI Setting MDI-X Setting
Pin Signal Pin Signal
1 Transmit + 1 Receive +
2 Transmit - 2 Receive -
3 Receive + 3 Transmit +
6 Receive - 6 Transmit -
Pin Signal Pin Signal
1 NOT USED 5 DSR - Data Set Ready
2 DTR - Data Terminal
Ready 6 SG - Signal Ground
3 TX - Transmit Data 7 RTS - Request To Send
4 RX - Receive Data 8 CTS - Clear To Send
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with this instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can
void your right to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
1 2 3 4 5 6 7 8 7 6
5 2 4 1 3
RJ-45 RS-232
4 5 6