Allied Telesis AT-PWR3201 - Manual (Page 2)

2. On the back of the AT-RPS3204, locate the power
switch that corresponds to the slot where you are going
to install the power supply and verify that the On/Off
button is in the Off (out) position. From left to right on
the back, the power supplies are identified as B2, B1,
A2, A1. (An AT-RPS3204 is shipped with one
AT-PWR3201 in the slot marked A1.)
3. Using a Phillips head screwdriver, remove the cover
from the slot in the front of the AT-RPS3204 where you
want to install the power supply.
Note
As an example, the following steps show an
AT-PWR3201 being installed in slot A2.
Keep the slot cover in a safe area in case you remove
a power supply. The slot cover helps maintain proper
air flow through the RPS.
4. Slide the AT-PWR3201 Power Supply into the slot.
5. Use a Phillips head screwdriver to tighten the captive
screws.
AT-PW R320 1
STATUS
POWER
FAULT
12VD C ,10A MAX
AT-PWR3201
STATUS
POWER
FAULT
12VDC ,10A MAX
405
AT-PW R3201
STATUS
POWER
FAULT
12VD C ,10A MAX
AT-PW R3201
STATUS
POWER
FAULT
12VD C ,1 0A M AX
406
AT-PWR3201
STA TUS
POWER
FAULT
12VDC ,10A MA X
AT-PW R3201
STATUS
POWER
FAULT
12VD C ,10A MAX
AT-PW R3201
STATUS
POWER
FAULT
12VD C ,10A M AX
407
AT-PWR3201
STATUS
POW ER FAULT
12V DC ,10A MAX
6. On the back of the AT-RPS3204, plug one end of the
21-pin D-combo connector cable into the connector
that corresponds to the slot in which you installed the
AT-RPS3201 power supply.
7. Tighten the captive screws.
8. Plug the other end of the cable into the connector
labeled “RPS INPUT” on the back of the AT-9400
Series switch.
9. Tighten the captive screws.
10. Press the On/Off switch for that power supply to move
it to the On (in) position.
198
RPS O UTPU T A2 12VDC
RPS OUTPU
T A1 12VDC
AC INPUT A2/A
1 100 - 2 40 VA C ~
ON OFF
ON OFF
A1
A2
199
RPS OUTPU
T A2 12VDC
RPS O UTPU T A1 12VDC
AC INPUT A2/A
1 100 - 2 40 VA C ~
ON OFF
ON OFF
A1
A2
RPS INPU
T
400
RPS INPU
T
401
402
RPS OUTPU
T A2 12VDC
RPS OUTPU
T A1 12VDC
AC INPUT A2/A
1 100 - 2 40 VA C ~
ON OFF
ON
OFF A1
A2
2. On the back of the AT-RPS3204, locate the power
switch that corresponds to the slot where you are
going to install the power supply and verify that the On/
Off button is in the Off (out) position. From left to right
on the back, the power supplies are identified as B2,
B1, A2, A1. (An AT-RPS3204 is shipped with one
AT-PWR3201 in the slot marked A1.)
3. Using a Phillips head screwdriver, remove the cover
from the slot in the front of the AT-RPS3204 where you
want to install the power supply.
Note
As an example, the following steps show an
AT-PWR3201 being installed in slot A2.
Keep the slot cover in a safe area in case you remove
a power supply. The slot cover helps maintain proper
air flow through the RPS.
4. Slide the AT-PWR3201 Power Supply into the slot.
5. Use a Phillips head screwdriver to tighten the captive
screws.
AT-PW
R3201
STATUS
POWER
FAULT
12VD C ,1 0A M AX
AT-PWR3201
STATUS
POWER
FAULT
12VDC ,10A MAX
405
AT-PW R3201
STATUS
POWER
FAULT
12VD C ,10A MAX
AT-PW R3201
STATUS
POWER
FAULT
12VD C ,1 0A M AX
406
AT-PWR3201
STA TUS
POWER
FAULT
12VDC ,10A MA X
AT-PW R3201
STATUS
POWER
FAULT
12VD C ,10A MAX
AT-PW R320 1
STATUS
POWER
FAULT
12VD C ,10A M AX
407
AT-PWR3201
STATUS
POW ER FAULT
12VDC ,10A MAX
6. On the back of the AT-RPS3204, plug one end of the
21-pin D-combo connector cable into the connector
that corresponds to the slot in which you installed the
AT-RPS3201 power supply.
7. Tighten the captive screws.
8. Plug the other end of the cable into the connector
labeled “RPS INPUT” on the back of the AT-9400
Series switch.
9. Tighten the captive screws.
10. Press the On/Off switch for that power supply to move
it to the On (in) position.
198
RPS OUTPU
T A2 12VDC
RPS OUTPU
T A1 12VDC
AC INPUT A2/A
1 100 - 2 40 VA C ~
ON OFF
ON OFF
A1
A2
199
RPS OUTPU
T A2 12VDC
RPS OUTPU
T A1 12VDC
AC INPUT A2/A
1 100 - 2 40 VA C ~
ON OFF
ON OFF
A1
A2
RPS INPU
T
400
RPS INPU
T
401
402
RPS OUTPU
T A2 12VDC
RPS OUTPU
T A1 12VDC
AC INPUT A2/A
1 100 - 2 40 VA C ~
ON OFF
ON OFF
A1
A2