Allied Telesis AT-PWR3201 - Manual

PN 613-50656-00 Rev. A PN 613-50656-00 Rev. A
AT-PWR3201 Power Supply
Installation Guide
Overview
The AT-PWR3201 Power Supply is designed to be installed
in an AT-RPS3204 Redundant Power Supply (RPS). The
RPS can supply power to an AT-9400 Series switch if the
switch’s main power supply fails.
Related Documents
For details on the features and functions of your AT-9400
Series switch, refer to the following document on our web
site, www.alliedtelesyn.com:
• AT-9400 Series Switches Installation Guide
(part number 613-50569-00)
Verifying Package Contents
Verify that the correct components are included in your
package:
• AT-PWR3201 Power Supply
• One 21-pin D-combo connector cable
• This installation guide
• Warranty card
If any item is missing or damaged, contact your Allied
Telesyn sales representative for assistance.
Installing the Power Supply
To install an AT-PWR3201 Power Supply, perform the
following procedure:
1. Remove the AT-PWR3201 power supply from its
shipping package and store the package in a safe
place. You must use the original package if you need to
return the power supply to Allied Telesyn.
404
AT-PW R3201
STATUS
POWER
FAULT
12VDC
,10A MAX
The RPS LED on the front of the AT-9400 Series switch
should be green. For more information about the RPS LED,
refer to the AT-9400 Series Switches Installation Guide.
Specifications
Electrical Safety and Emission Statement
This product meets the following standards.
RFI Emissions EN 55022 Class A
Warning
In a domestic environment this product may cause
radio interference in which case the user may be
required to take adequate measures.
Immunity EN 55024
Electrical Safety UL 60950 (
C
UL
US
), EN 60950 (TUV)
Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of
this publication may be reproduced without prior written permission
from Allied Telesyn, Inc. www.alliedtelesyn.com
Item Specification
Dimensions (H x W x D) 41.1 x 109 x 248.7 mm
(1.62 x 4.29 x 9.79 in.)
Operating Temperature 0° C to 40° C
Storage Temperature -20° C to 80° C
Relative Humidity <85% noncondensing
Supply Voltage 12 V
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Note: Modifications or changes not expressly approved of by the
manufacturer or the FCC, can void your right to operate this
equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.
AT-PWR3201 Power Supply
Installation Guide
Overview
The AT-PWR3201 Power Supply is designed to be installed
in an AT-RPS3204 Redundant Power Supply (RPS). The
RPS can supply power to an AT-9400 Series switch if the
switch’s main power supply fails.
Related Documents
For details on the features and functions of your AT-9400
Series switch, refer to the following document on our web
site, www.alliedtelesyn.com:
• AT-9400 Series Switches Installation Guide
(part number 613-50569-00)
Verifying Package Contents
Verify that the correct components are included in your
package:
• AT-PWR3201 Power Supply
• One 21-pin D-combo connector cable
• This installation guide
• Warranty card
If any item is missing or damaged, contact your Allied
Telesyn sales representative for assistance.
Installing the Power Supply
To install an AT-PWR3201 Power Supply, perform the
following procedure:
1. Remove the AT-PWR3201 power supply from its
shipping package and store the package in a safe
place. You must use the original package if you need
to return the power supply to Allied Telesyn.
404
AT-PW R3201
STATUS
POWER
FAULT
12VDC
,10A MAX
The RPS LED on the front of the AT-9400 Series switch
should be green. For more information about the RPS LED,
refer to the AT-9400 Series Switches Installation Guide.
Specifications
Electrical Safety and Emission Statement
This product meets the following standards.
RFI Emissions EN 55022 Class A
Warning
In a domestic environment this product may cause
radio interference in which case the user may be
required to take adequate measures.
Immunity EN 55024
Electrical Safety UL 60950 (
C
UL
US
), EN 60950 (TUV)
Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of
this publication may be reproduced without prior written permission
from Allied Telesyn, Inc. www.alliedtelesyn.com
Item Specification
Dimensions (H x W x D) 41.1 x 109 x 248.7 mm
(1.62 x 4.29 x 9.79 in.)
Operating Temperature 0° C to 40° C
Storage Temperature -20° C to 80° C
Relative Humidity <85% noncondensing
Supply Voltage 12 V
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Note: Modifications or changes not expressly approved of by the
manufacturer or the FCC, can void your right to operate this
equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.