Samsung PS50B530S2W - Manual (Page 31)

English - 31
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1. Press the TOOLS button. Press the ENTERE button to select Anynet+ (HDMI-CEC).
2. Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select
On or Off.
If your receiver supports audio only, it may not appear in the device list.
N
The receiver will work when you have properly connected the Optical IN jack of the
N
receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound output from the N
TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1
channel sound to the Home theater receiver. When the source is a digital component
such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
If there is a power interruption to the TV when the
N
Receiver is set to On (by disconnecting the power cord or a power failure),
the Speaker Select may be set to External Speaker when you turn the TV on again. (see page 22)
Troubleshooting for Anynet+
Symptom Solution
Anynet+ does not work. Check if the device is an Anynet • + device. The Anynet+ system supports Anynet+ devices only.
Connect only one receiver (home theater). •
Check if the Anynet • + device power cord is properly connected.
Check the Anynet • + device’s Video/Audio/HDMI 1.3 cable connections.
Check whether • Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
Check whether the TV remote control is in TV mode. •
Check whether it is Anynet • + exclusive remote control.
Anynet • + doesn’t work in certain situations. (Searching channels, Operating Plug & Play, etc.)
When connecting or removing the HDMI 1.3 cable, please make sure to search devices again •
or turn your TV off and on again.
Check if the Anynet • + Function of Anynet+ device is set on.
I want to start Anynet+. Check if the Anynet+ device is properly connected to the TV and check if the • Anynet+
(HDMI-CEC) is set to On in the Anynet+ Setup menu.
Press the • TV button on the TV remote control to switch to TV. Then press the TOOLS button
to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+. Select View TV in the Anynet • + menu.
Press the • SOURCE button on the TV remote control and select a device other than Anynet+
devices.
(Note that the channel button operates only when a tuner-embedded Anynet • + device is not
connected.)
The message Connecting to
Anynet+ device...
appears on the screen.
You cannot use the remote control when you are configuring Anynet • + or switching to a view
mode.
Use the remote control when the Anynet • + setting or switching to view mode is complete.
The Anynet+ device does not
play.
You cannot use the play function when • Plug & Play is in progress.
The connected device is not
displayed.
Check whether or not the device supports Anynet • + functions.
Check whether or not the HDMI 1.3 cable is properly connected. •
Check whether • Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
Search Anynet • + devices again.
You can connect an Anynet • + device using the HDMI 1.3 cable only. Some HDMI cables may
not support Anynet+ functions.
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power •
cord or a power failure, please repeat the device scan.
The TV programme cannot be
recorded.
Check whether the antenna jack on the recording device is properly connected. •
The TV sound is not output
through the receiver.
Connect the optical cable between TV and the receiver. •
View TV
Device List
Record
: DVDR
DVDR MENU
DVDR INFO
Receiver
◄ On ►
Setup
U Move L Adjust R Return
BN68-02355A-Eng.indb 31 2009-06-30 �� 10:26:11