Samsung SH-W162L-LCAH - Manual (Page 31)

Specifications
Category
SH-W162L(TS-H552L)
DVD±R/RW Drive
DISC
Usable Discs
DVD : DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-ROM,
DVD-Video, DVD+R (Dual), DVD-R (Dual)
CD : CD-ROM, CD-R, CD-RW, CD-DA, CD+E(G)
CD-MIDI, CD-TEXT, CD-ROM XA, Mixed Mode CD
CD-I, CD-I Bridge (Photo-CD, Video-CD),
Multisession CD (Photo-CD, CD-EXTRA, Portforio)
Disc Diameter 4.72 Inch or 3.15 Inch (120mm or 80mm)
Interface Support
Interface Port ATA/ATAPI (E-IDE)
PIO mode PIO Mode 4: 16.6MB/sec
DMA mode Ultra DMA Mode 2: 33.3MB/sec
ACCESS TIME (Random)
CD-ROM 110ms (Random)
DVD-ROM 130ms (Random)
Writing
Time
Setting Titles only TTitles and contents
The entire label area
(including graphics)
Best Less than 4 min Less than 9 min Less than 36 minutes
Normal Less than 3 min Less than 7 min Less than 28 minutes
Draft Less than 2 min Less than 4 min Less than 20 minutes
Data Transfer Speed
(Max)
Media Type Write Read
DVD+R PCAV 16X (21.6MB/sec) CAV 12X (16.2MB/sec)
DVD+RW Z-CLV 8X (10.8MB/sec) CAV 8X (10.8MB/sec)
DVD+R DUAL Z-CLV 8X (10.8MB/sec) CAV 8X (10.8MB/sec)
DVD-R DUAL Z-CLV 4X (5.4MB/sec) CAV 8X (10.8MB/sec)
DVD-R PCAV 16X (21.6MB/sec) CAV 12X (16.2MB/sec)
DVD-RW Z-CLV 6X (8.1MB/sec) CAV 8X (10.8MB/sec)
DVD-ROM(Single) - CAV 16X (21.6MB/sec)
DVD-ROM(Dual) - CAV 8X (10.8MB/sec)
CD-ROM - CAV 40X (6.0MB/sec)
CD-R PCAV 48X (7.2MB/sec) CAV 40X (6.0MB/sec)
US-RW PCAV 32X (4.8MB/sec) CAV 40X (6.0MB/sec)
HS-RW CLV 10X (1.5MB/sec) CAV 40X (6.0MB/sec)
CD-RW CLV 4X (0.6MB/sec) CAV 40X (6.0MB/sec)
Buffer Memory 2MB
Drive Installation Horizontal / Vertical
Operating Environment
Temperature 41°F ~ 122°F (5°C ~ 45°C)
Humidity 10% ~ 80% (RH)
Size(Width x Height x Length) 5.34 X 1.65 X 7.24 Inch (148.2 X 42 X 184mm)
Weight 760g
MTBF 125,000 POH(Duty 20%)
Note
Does not support DVD-R for Authoring, DVD-RAM
Cannot playback or record on both sides of a two-sided disc simultaneously.
The read/write capacity of the supported discs depends on the condition of the disc
and the recording format of the drive. Therefore, the read/write quality may not be perfect.
Severe vibration or external impact may decrease the quality of printed images.
Please firmly place the product onto the PC before use.
In case of disk identification error message, thoroughly clean the surface of the disk
where the label is presented and then start printing.
The quality of the printed image cannot be ensured if printing an image on the area
which is already used for printing.
For more information on the writing and duplicating the Lightscribe disk label,
install Nero software and refer to the HELP section.