Campbell Scientific PST3/PST8 Pump and Slug Test System - Manual (Page 27)

SECTION 5. TECHNICAL DETAILS
5-2
1= EDLOG Datalogger Program
Editor
2= GRAPHTERM Terminal
Emulator
3= TELCOM Data Collection
Program
4= SPLIT Data Split/Merge
Program
5= SMCOM Storage Module
Communications
(SM192/716)
6= All of the above
Enter a list of digits
corresponding to what you
want installed:
HARD DISK
If installing the PC208 software on a hard disk
or a diskette with 1.2 megabytes or greater,
then select 6 to install all the programs on the
specific drive.
FLOPPIES
If installing the PC208 software on 360 K
floppies, then run the Install program two
separate times. It will require two formatted
floppies, and the floppies should be blank
(without the system on them). The first time,
select 2 and 3 for GraphTerm and TELCOM.
Next, select 4 for SPLIT.
5.3.3 RUNNING PCPST FROM A FLOPPY DISK
PC208 should be in the root directory of the
work diskette, or in drive B: with "B:\" in your
DOS PATH. See your DOS reference for more
information on the DOS PATH.
5.3.4 INSTALLATION WITHOUT A HARD DISK
1. Insert the work PCPST diskette into the
desired floppy drive. Then, change to that
drive and start the program. For example,
to run PCPST from drive A:, you should
insert the work diskette into drive A: and
type the following:
a:
PST
2. Data will be collected into a subdirectory
named "DATA" on your work diskette.
Continuing the above example, you can see
a list of your data files by typing the
following:
dir data (if you are in the root
directory of A:)
OR
dir a:\data
(if you are in some other drive
or directory)
3. For floppy disk operations, available data
space may be small. For example, if
PCPST and the necessary PC208 program
files were copied onto a 720 Kbyte diskette,
there would be only about 70 Kbytes
available for data storage on the diskette.
5.3.5 PROGRAM FILES:
PCPST program files:
COLORS.BAT INSTALL.BAT PST.EXE
PST3.BAT PST8.BAT README.BAT
VIEWER.BAT
Auxiliary files used by PCPST are kept in
subdirectory PSTPAR. Normally, you will not
need to be concerned with the auxiliary files.
Most of the files in subdirectory PSTPAR are
parameter files used by PC208/SPLIT to
convert data. The following is a listing of
subdirectory PSTPAR:
[.] [..] AQSDEL1.PAR
AQSDEL2.PAR AQSDEL3.PAR AQSDEL4.PAR
AQSDEL5.PAR AQSDEL6.PAR AQSDEL7.PAR
AQSDEL8.PAR AQSLOG1.PAR AQSLOG2.PAR
AQSLOG3.PAR AQSLOG4.PAR AQSLOG5.PAR
AQSLOG6.PAR AQSLOG7.PAR AQSLOG8.PAR
COLORS COLORS.BAT COMPORT
DELCLK1.PAR DELCLK2.PAR DELCLK3.PAR
DELCLK4.PAR DELCLK5.PAR DELCLK6.PAR
DELCLK7.PAR DELCLK8.PAR DELLAP1.PAR
DELLAP2.PAR DELLAP3.PAR DELLAP4.PAR
DELLAP5.PAR DELLAP6.PAR DELLAP7.PAR
DELLAP8.PAR LOGCLK3.PAR LOGCLK8.PAR
LOGLAP3.PAR LOGLAP8.PAR PST33.DLD
PST83.DLD README.DOC SM.STN
SM1.STN SM2.STN SM3.STN
SM4.STN VIEW.COM VIEWER.BAT
VIEWER WELL.STN WELL1.STN
WELL2.STN WELL3.STN WELL4.STN
PC208 program files installed and used by
PCPST are:
GT.EXE For some communications
SMCOM.COM For erasing a storage
module
SPLIT.COM
For data conversion
SPLIT.001 For data conversion
SPLIT.002 For data conversion
SPLIT.003 For data conversion
SPLIT.004 For data conversion
TELCOM.EXE For data retrieval