Accusplit AE120XLM - Manual (Page 3)

REPLACING THE BATTERY AND MASTER RESET
When the display starts to dim or goes blank, it is time to
replace the battery.
If the display is not uniformly dim or blank, and appears to
display “erroneous data”, do a Master Reset by pressing all
3 buttons simultaneously for 3 seconds and then release.
The display should go blank, then turn all segments on, then
display 0 steps in Step Mode.
Note: All the settings will return to their default setting values.
If you need to change the battery, the settings will also revert
to default settings.
CHANGING STEP FILTER SETTING
While the JW200 PedometerEngine™ Step Sensor is extremely
accurate, some people like to have the ability to filter out false
steps. Therefore, the unit has a variable setting step filter, to
allow fine-tuning to your specific preferences. You can set the
value to any value from 0 – 5 steps. For example, if the filter is
set to “3”, the unit will wait to start counting steps until more
than three steps have been taken in less than five seconds.
Press and hold the S1 (MEMORY) button for 4 seconds. The
screen will display a single digit. Press S3+ (MODE) or S3–
(RESET) to change the Step Filter Setting. Press and hold S4
(Memory) for 2 seconds to exit Deep Set Mode.
Note: The unit will save any changes and exit set mode after
30 second unattended.
18 19
17
23
20 21
22
OTHER SETTINGS
The Step Filter setting is accessed through a special “deep
set” mode.
ACCUSPLIT products use a common setting procedure
known as “S1- S2-S3-S4.” Here’s how it works:
Press S1 for 2 seconds: Enter the SET mode
Press S2: Change the field to be set
Press S3: Change the field value
Press S4 for 2 seconds: Exit the SET mode
Set Step Filter set point
STEP TIME SET
D IGI - W ALKER XL .COM
120 XL M
S3- S3+ S1,S2,S4
JW200
Can be set
from 0-5
steps
Battery
To replace the battery:
1. Insert a coin into the slot on the
bottom of the case, and twist to
loosen the faceplate. Remove
faceplate and set aside.
2. Locate the battery holder as seen
on sketch. Pull out the old battery,
and push a new LR-44 battery into the holder,
with positive terminal (+) facing up.
3. Snap faceplate back into place, hooking the bottom
two tabs first, then closing by pressing together at the
top two tabs. SPECIFICATIONS, FEATURES, and FUNCTIONS
Description of Functions
• Counts Steps up to 99,999 then rollover.
• Has a Total Memory for Steps that counts up to 99,999,999
steps, then rollover.
• Counts Time spent in step activity, up to 999 Min 59 sec,
then rollover. Automatically counts whenever step activity
is occurring.
• Has a Total Memory for Activity Time that counts up to
99,999 minutes, then rollover.
• Adjustable Step Filter (default setting is 1 step, but can
be set from 0-5 steps) to increase step count accuracy.
REGISTER NOW Please return
your AE120XLM Registration to
the Repair Center address in the
warranty, and we will let you know
about future products.
Email (preferred)
User
NO-PROOF-OF-PURCHASE LIMITED WARRANTY
Free service for first year of ownership;
$12 fee for service thereafter. See label inside unit for date.
See www.ACCUSPLIT.com/support for details
Battery, replacing . . . . . . . . . . . . . . . . . . 19-20
Current day’s results, viewing . . . . . . . . . . .11
Memory, resetting . . . . . . . . . . . . . . . . . . . 15
Open your pedometer . . . . . . . . . . . . . . . . . 4
Safety Leash . . . . . . . . . . . . . . . . . . . . . . . 9-10
Setting up pedometer. . . . . . . . . . . . . . . . 6-11
Step Filter Setting, change. . . . . . . . . . . 16-18
TOTAL vs TRIP Memories . . . . . . . . . . . . 12-13
Wearing pedometer . . . . . . . . . . . . . . . . . . . 8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
INDEX
16