Arcam AVR Surround Amplifer AV888 - Manual (Page 28)

E-26
��� aMP device Mode
The A Device Mode button configures the CR102 to
control the AVR600/AV888. Pressing this button does
not affect the currently selected input on the AVR600/
AV888.
IMPORTANT: The CR102 must also be in
AMp Device
Mode to control the following sources: phono , MCh
(multichannel analogue), AuX , nET (optional network
audio), uSB , ipoD (for use with the optional Arcam
rLead or rDock).
However to control the internal Tuner in the AVR600
(AM/FM/DAB or Sirius if fitted), the CR102 must first
be in Tun Device Mode (see later).
The functionality of the CR102 is context sensitive for
the internal sources and is described in the following
table.
P Single press – Toggles AVR600/AV888
power between standby and on in the
current zone (zone in which the command
is received).
Press and hold – Forces all AVR600/AV888
zones into standby, regardless of which zone
the command was received in.
0 … 9 The number keys can be used for source
selection (without changing the CR102
Device Mode). Alternatively the Device
Mode buttons can also be used with the
ShiFT key.
0 SAT (satellite) input
1 phono input
2 AV input
3 TunER input
4 DVD input
5 TApE input
6 VCR input
7 CD input
8 AuX (front panel) input
9 MCh (multichannel) input
PHONO
E
Selects Tape input on the AVR600/AV888
ShiFT + E selects phono input on the
AVR600/AV888
RPT
r
(for ipoD and nET sources)
S Modifies many keys (see individual key
descriptions below).
AUX
H
Selects MCh (multichannel) input on the
AVR600/AV888
ShiFT + H selects AuX input on the
AVR600/AV888
��
Navigate menus
oK confirms a setting (equivalent to ‘Enter’
or ‘Select’ on some remote controls)
Press and hold
oK to force the analogue
and digital video outputs to the default
resolution: 480i (525-line NTSC).
ShiFT + < decreases the picture resolution.
ShiFT + > increases the picture resolution.
ShiFT + ' turns current zone (in which
command is received) on
ShiFT + , turns current zone (in which
command is received) off.
NET
e
Selects ipoD input on the AVR600/AV888
ShiFT + e selects network ( nET ) internal
input on the AVR600/AV888
M Cycles through the available surround and
downmix modes.
U Displays the AVR600/AV888 setup menu
on the On Screen Display (see page 34).
D Cycles through the front panel display’s
brightness options
@ Toggles the mute function of the AVR600/
AV888
] [ (track control for ipoD and nET sources)
ShiFT + [ Follow Zone1 source.
When the command is received in Zone2
or Zone3, the source for that zone follows
whatever input source is selected in Zone1
- + Decrease ( – ) and increase ( + ) AVR600/
AV888 volume
DIRECT
)
Stereo direct on/off. Provides a direct
analogue path from the analogue inputs to
the left and right front outputs. Switches off
any surround processing modes and shuts
down the DSP circuits for the best stereo
sound quality.
EQ
$
Displays the room EQ settings menu
EFFECT
&
(for ipoD and nET sources)
BASS
(
Calls up a pop-up (and front screen) to
adjust the bass setting for a particular input.
TRIm
!
Brings up the speaker trim menu.
Use the
B , C , D and E navigation
buttons. Press TRiM again to exit the speaker
trim menu.
As this is a temporary adjustment, these
additional trim levels are reset to zero when
the unit is turned off or the selected input is
changed, but are retained if the unit is put
into standby. These temporary trim levels
are independent of the speaker levels found
in the setup menu.
SyNC
#
Delays may be introduced into the video
signal by video processing which causes
a mismatch between the audio and video
timing. You will notice this by speech sound
being out of synchronization with the lip
movements in the video.
To compensate for this, you can adjust the
lip sync delay. Press the SynC button and
use the D and E navigation buttons. Press
again to exit the lip sync trim menu.
SUB
%
Brings up the subwoofer trim menu. Use
the D and E navigation buttons. Press SuB
again to exit the sub trim menu
TREBLE
h
Calls up a pop-up (and front screen) to
adjust the treble setting for a particular
input.
FAV+
u
(for ipoD and nET sources)
FAV-
t
(for ipoD and nET sources)
HOmE
o
(for ipoD and nET sources)
INFO
b
Cycles through the information displayed
on the lower left portion of the front panel
display.
iPod commands
The iPod interface is selected by pressing e in AMp
Device Mode on the CR102. When connected to an
iPod via an optional rLead/rDock, the keys below are
used to navigate music files in AMp Device Mode.
��
Navigate the files on screen.
oK selects/play the highlighted file.
RPT
r
Toggles random (shuffle) play of the playlist
on and off.
ShiFT + r cycles through the repeat options
] [ Selects the previous/next track in the
current playlist
$ Begins or resumes playback at the currently
highlighted track
& Toggles pause and playback of the current
track
# Stops playback