State Tilt Roof User Manual
Page 3
3
TILT
ANGLE
4” MOUNTING
STRUT
(see Figure 4.)
4” C-CHANNEL
(see Figure 3.)
6 PLACES PER COLLECTOR
STAINLESS STEEL BOLT,
FLAT WASHER, LOCK WASHER,
& NUT (see Figures 3-5.)
C-CHANNEL
TILT RISER
UPPER COLLECTOR
LOWER COLLECTOR
COLLECTOR
MOUNTING
STRUT
“G”
“F”
“H”
+25,=217$/ 7,/7 02817,1*
Locate the mounting points for the mounting brackets per
)LJXUH )LJXUH
7DEOH /D\RXW WKH URRI DV VSHFL¿HG LQ
the solar installation manual or the optional solar collector
mounting kit being used. Keep in mind the “H” dimension
listed in Table 2 when marking the mounting points.
1. Install the solar collector mounting hardware included
with the solar collector crate package or the optional
solar collector mounting kit following their instructions
EXW XVLQJ WKH URRI OD\RXW DV VSHFL¿HG LQ WKHVH
instructions for your particular tilt kit.
2. Install the 4” mounting bracket strut to the upper
collector mounting location with the stainless steel
fasteners included with your solar collector crate
package or other optional solar collector mounting kit.
See Figure 6 for placement of mounting bracket strut.
3. Install the 4” C-Channel mounting bracket to the
lower collector mounting location with the stainless
steel fasteners included with your solar collector crate
package or other optional solar collector mounting kit.
See Figure 6 for placement of C-Channel mounting
bracket.
4. Locate the C-Channel Tilt Risers included with your kit.
This tilt riser leg will need to be cut-to-length with a
hack saw or other suitable tool to match the “G” length
noted in Table 2 for the solar collector size being used
and tilt angle that is desired. See Table 2 and Figure 8.
5. Drill a 3/8” hole through the “cut” end of the C-Channel
Tilt Riser as depicted in Figure 8.
6. Install the C-Channel Tilt Riser to the upper 4” mounting
bracket strut with the included stainless steel hex bolt,
ORFN ZDVKHU ÀDW ZDVKHU DQG KH[ QXW 6HH )LJXUH
Figure 6.
7. Locate the Collector Mounting Struts included with
your kit. This mounting strut will be need to be cut to
length with a hack saw or other suitable tool to match
the “H” length noted in Table 2 for the solar collector
size being used and tilt angle that is desired. See Table
2 and Figure 9.
8. Drill a 3/8” hole through the “cut” end of the Collector
Mounting Strut as depicted in Figure 9.
9. Install one end of the Collector Mounting Strut to the
lower 4” C-Channel mounting bracket with the included
VWDLQOHVV VWHHO KH[ EROW ORFN ZDVKHU ÀDW ZDVKHU DQG
hex nut. See Figure 4 & Figure 6.
10. Install the other end of the Collector Mounting Strut
to the loose end of the C-Channel Tilt Riser with the
LQFOXGHG VWDLQOHVV VWHHO KH[ EROW ORFN ZDVKHU ÀDW
washer, and hex nut. See Figure 5 & Figure 6.
11. Repeat steps 2 - 10 including Figure 7 for the remainder
of the mounting bracket locations.
Figure 6.
&2//(&725
7,/7 $1*/(
“F” MOUNTING
%5$&.(7
SPACING
³*´ /(1*7+
³+´ /(1*7+
“J”
“K”
Horiz 3.5’ X 7’
15°
44.00
13.25
48.50
62
28
30°
40.25
24.75
45°
31.75
34.50
60°
20.50
42.00
75°
9.00
46.75
Horiz 4’ X 8’
15°
50.00
14.75
54.50
72
30°
45.25
27.50
45°
37.50
38.50
60°
27.75
47.00
75°
14.75
52.25
Horiz 4’ X 10’
15°
50.00
14.75
94
30
30°
45.25
27.50
45°
37.50
38.50
60°
27.75
47.00
75°
14.75
52.25
Table 2.
All Dimensions in Inches