State Tilt Roof - Manual

1
fasteners included with your solar collector crate
package or other optional solar collector mounting kit.
See Figure 1 for placement of mounting bracket strut.
3. Install the 4” C-Channel mounting bracket to the
lower collector mounting location with the stainless
steel fasteners included with your solar collector crate
package or other optional solar collector mounting kit.
See Figure 1 for placement of C-Channel mounting
bracket.
4. Locate the C-Channel Tilt Riser included with your
kit. Install this to the upper 4” Mounting strut with the
LQFOXGHG VWDLQOHVV VWHHO KH[ EROW ÀDW ZDVKHU ORFN
washer, and hex nut. See Figure 1 & Figure 4.
5. Locate the Collector Mounting Struts included with
your kit. Install one of these to the lower 4” C-Channel
mounting bracket with the included stainless steel hex
EROW ÀDW ZDVKHU ORFN ZDVKHU DQG KH[ QXW SHU )LJXUH
6. Install the other end of the collector mounting strut
to the upper end of the C-Channel Tilt Riser with the
LQFOXGHG VWDLQOHVV VWHHO KH[ EROW ORFN ZDVKHU ÀDW
washer, and hex nut. See Figure 1 & Figure 5.
7. Repeat steps 2 - 6 including Figure 2 for the remainder
of the mounting bracket locations.
125 Southeast Parkway, Franklin, TN 37068
3+21( ‡ )$;
62/$5 &2//(&725 7,/7 02817 ,16758&7,216
The solar collector mounting hardware in this kit is an
addition to the solar collector mounting hardware that
is included in the solar collector crate package or other
optional solar collector mounting kits. Refer to your solar
system instruction manual and/or the optional solar collector
mounting kit instructions for the installation of these
components. Call the technical support center at 1-800-
433-2545 if further technical assistance is required. Solar
collector tilt mount kits are available for angles up to 75° in
15° increments. See Table 1 for vertical mounting and Table
2 for horizontal mounting.
9(57,&$/ 7,/7 02817,1*
Locate the mounting points for the mounting brackets per
)LJXUH )LJXUH
7DEOH /D\RXW WKH URRI DV VSHFL¿HG LQ
the solar installation manual or the optional solar collector
mounting kit being used. Keep in mind the “A” dimension
listed in Table 1 when marking the mounting points.
1. Install the solar collector mounting hardware included
with the solar collector crate package or the optional
solar collector mounting kit following their instructions.
2. Install the 4” mounting bracket strut to the upper
collector mounting location with the stainless steel
Preserving the integrity of the roof membrane is the
PRVW LPSRUWDQW URR¿QJ FRQVLGHUDWLRQ (QVXUH WKDW DOO
roof penetrations required to plumb and mount the solar
FROOHFWRU DUH SURSHUO\ ÀDVKHG DQG VHDOHG LQ DFFRUGDQFH
ZLWK VWDQGDUG URR¿QJ SUDFWLFHV
If the region is subject to hurricane conditions, additional
steps may be required to secure the collector and mounting
hardware to the structural members. In certain areas of the
country, local building codes may require collector wind
ORDG WHVWLQJ RU SUHVFULEH VSHFL¿F PRXQWLQJ SURFHGXUHV
Consult your local building department.
Install the collectors as described in the Tilt Mounting
instructions.
62/$5 25,(17$7,21
For optimal performance all during the year, the proper tilt
angle for solar collectors is latitude plus 10°. This additional
10° tilt improves performance in the winter when the sun
is weaker and at a lower angle. The cost in performance
in the summer when the sun is high is overcome by the
hours of sunlight and strength of irradiation that occurs
during the summer months.
CAUTION
ALL PERSONS WORKING ON ROOFS SHOULD
HAVE SUCCESSFULLY COMPLETED A FALL SAFETY
COURSE AND SHOULD BE PROPERLY EQUIPPED
WITH THE APPROPRIATE SAFETY EQUIPMENT
AFTER COMPLETION OF THE COLLECTOR
MOUNTING AND PRIOR TO SYSTEM CHARGING THE
COLLECTORS MUST BE COVERED BY A BLANKET OR
OTHER MEANS TO AVOID SOLAR RADIATION FROM
HEATING THE COLLECTORS. THE SURFACES OF THE
COLLECTOR CAN BECOME EXTREMELY HOT AND
COULD POSE A BURN HAZARD.
WARNING
The most important structural consideration is to securely
anchor the solar collector and the mounting hardware to
the structural members of the roof with the stainless steel
hardware provided. The solar collector must be attached
to the mounting hardware as detailed in Figure 10.
Drill & Drill Bits (3/8” & 5/16)
Saw (Hacksaw)
([WHQVLRQ &RUG
Tape Measure
Chalk Line
Utility Knife
Level
Pliers Angle Indicator
8” & 10” Adjustable Wrenches
7/16” & 9/16” Wrenches
Ratchet w/ 7/16” & 9/16” Sockets
6’ x 8’ or 6’ x 10’ Tarp (1 per collector)
Installation Hardware (Supplied) Includes:
‡
Hardware
‡ Mounting Brackets
%$6,& 722/6 $1' 0$7(5,$/6
35,17('