Asus Motherboard P5VD2-MX - Manual (Page 46)

1 - 3 4 1 - 3 4 1 - 3 4 1 - 3 4 1 - 3 4 C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
1 1 . 1 1 . 1 1 . 1 1 . 1 1 . Front panel audio connector (10-1 pin AAFP) F r o n t p a n e l a u d i o c o n n e c t o r ( 1 0 - 1 p i n A A F P ) F r o n t p a n e l a u d i o c o n n e c t o r ( 1 0 - 1 p i n A A F P ) F r o n t p a n e l a u d i o c o n n e c t o r ( 1 0 - 1 p i n A A F P ) F r o n t p a n e l a u d i o c o n n e c t o r ( 1 0 - 1 p i n A A F P )
This connector is for a chassis-mounted front panel audio I/O module
that supports either High Definition Audio or legacy AC ‘97 audio
standard. Connect one end of the front panel audio I/O module cable
to this connector.
• Use a chassis that provides a high-definition audio front panel audio
I/O to use the high-definition audio features.
• The default setting of this connector is legacy AC’97 audio, if you
want to use the High-Definition (Azalia) audio features, set the
F r o n t P a n e l S u p p o r t T y p e
F r o n t P a n e l S u p p o r t T y p e F r o n t P a n e l S u p p o r t T y p e F r o n t P a n e l S u p p o r t T y p e F r o n t P a n e l S u p p o r t T y p e in the BIOS to Azalia.
1 2 . 1 2 . 1 2 . 1 2 . 1 2 . Chassis intrusion connector (4-1 pin CHASSIS) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
®
Chassis intrusion connector
CHASSIS
+5VSB_MB Chassis Signal GND
(Default)
®
Analog front panel connector
AAFP
Legacy AC’97-compliant
pin definition
NC
MIC2
Line out_R Line out_L
NC
NC
MICPWR
NC AGND
POR
T1 R
SENSE2_RETUR
POR
T1 L
POR
T2 R
POR
T2 L
SENSE1_RETUR
SENSE_SEND
PRESENCE# GND
Azalia-compliant
pin definition