Asus Motherboard P5VD2-MX - Manual (Page 41)

A S U S P 5 V D 2 - M X / P 5 V - V M D H A S U S P 5 V D 2 - M X / P 5 V - V M D H A S U S P 5 V D 2 - M X / P 5 V - V M D H A S U S P 5 V D 2 - M X / P 5 V - V M D H A S U S P 5 V D 2 - M X / P 5 V - V M D H 1 - 2 9 1 - 2 9 1 - 2 9 1 - 2 9 1 - 2 9
2 . 2 . 2 . 2 . 2 . P r i m a r y / S e c o n d a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E P r i m a r y / S e c o n d a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E P r i m a r y / S e c o n d a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E P r i m a r y / S e c o n d a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E P r i m a r y / S e c o n d a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E
[ b l u e ] ; 4 0 - 1 p i n S E C _ I D E [ b l a c k ] )
[ b l u e ] ; 4 0 - 1 p i n S E C _ I D E [ b l a c k ] ) [ b l u e ] ; 4 0 - 1 p i n S E C _ I D E [ b l a c k ] ) [ b l u e ] ; 4 0 - 1 p i n S E C _ I D E [ b l a c k ] ) [ b l u e ] ; 4 0 - 1 p i n S E C _ I D E [ b l a c k ] )
The onboard IDE connectors are for Ultra DMA 133/100/66 signal
cables. There are three connectors on each Ultra DMA 133/100/66
signal cable: blue, black, and gray. Connect the blue connector to the
motherboard's IDE connector, then select one of the following modes
to configure your device(s).
• Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
Black or gray
D r i v e j u m p e r D r i v e j u m p e r D r i v e j u m p e r D r i v e j u m p e r D r i v e j u m p e r M o d e M o d e M o d e M o d e M o d e C a b l e C a b l e C a b l e C a b l e C a b l e
s e t t i n g s e t t i n g s e t t i n g s e t t i n g s e t t i n g o f d e v i c e ( s ) o f d e v i c e ( s ) o f d e v i c e ( s ) o f d e v i c e ( s ) o f d e v i c e ( s ) c o n n e c t o r c o n n e c t o r c o n n e c t o r c o n n e c t o r c o n n e c t o r
Single device Cable-Select or Master - Black
Two devices Cable-Select Master Black
Slave Gray
Master Master
Slave Slave
®
IDE connectors
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE
PIN 1
PRI_IDE
If any device jumper is set as "Cable-Select," make sure all other device
jumpers have the same setting.