GE ZGP304NRSS - Manual (Page 26)

BURNER OUTPUT RATINGS: BTU/HR
• If the flames are too small or flutter,
turn the screw counterclockwise.
• If the flames are too large, turn the screw
clockwise.
E. Make the adjustment by slowly turning the screw
until flame appearance is correct.
Installation Instructions for Gas Conversion
8 ADJUST BURNER FLAMES
Normally, burners do not need further adjustment.
Make adjustments only when necessary.
A. Turn on the gas. Plug in electrical cord.
B. Turn all burners on highest setting and check
the flames. They should be blue in color. When
using LP gas, the flames may have some yellow
tipping at the ends of the flame. Foreign particles
in the gas line may cause an orange flame at first,
but this will soon disappear.
C. Turn the burner knob to “LO” while observing the
flame.
Adjust the setting of the upper row of flames using
the valve bypass screw as follows:
Adjustments must be made with two other burners
in operation on a medium setting. This prevents the
upper row of flames from being set too low, resulting
in the flame being extinguished when other burners
are turned on.
D. To adjust the flame, remove the knobs. Insert a small
flat-blade screwdriver into the hole in the center of
the valve stem to engage screw.
Once the conversion is complete and checked, fill out the conversion label and affix the label near the rating label. For ranges,
place the label beneath the control panel. For rangetops, place the label on the bottom of the unit.
NG (Natural) Gas, 5” W.C.P.
MODEL BURNER BTU
RATE
ORIFICE SIZE ID
ZGP48
ZGP36 ALL SURF. Main 16,800 0.075” (1.90mm) 190XN
BURNERS Simmer 1,200 0.002” (0.51mm) 51SL
ZGP304 RF BURNER
Main 16,800 0.075” (1.90mm) 190XN
Simmer 1,200 0.002” (0.51mm) 51SN
ZGP304 RR, LR, LF
Main
Simmer
8,800 0.050” (1.26mm) 126HXN
1,200 0.002” (0.51mm)
51SN
ALL GRILL 15,000 0.0689” (1.75mm) 0.069
ALL GRIDDLE 18,000 0.076” (1.93mm) 0.076
ZGP48/
ZGP36 BAKE MAIN
24,500
0.0886”
(2.25mm)
0.089
ZGP30 BAKE MAIN 23,500 0.0866” (2.20mm) 0.087
ZGP48 BAKE COMPANION 10,500 0.0531” (1.35mm) 0.053
ALL BROIL MAIN 12,500 0.063” (1.60mm) 160
ZGP48 BROIL COMPANION 9,000 0.052” (1.32mm) 132
LP (Propane) Gas, 10” W.C.P.
MODEL BURNER BTU
RATE
ORIFICE SIZE ID
ZGP48
ZGP36 ALL SURF. Main 13,800 0.043” (1.08mm) 108XL
BURNERS Simmer 1,200 0.013” (0.34mm) 34SL
ZGP304 RF BURNER
Main 13,800 0.043” (1.08mm) 108XL
Simmer 1,200 0.013” (0.34mm) 34SL
ZGP304 RR, LR, LF
Main
Simmer
7,900 0.033” (0.84mm) 84XL
1,200 0.013” (0.34mm) 34SL
ALL GRILL 14,000 0.047” (1.19mm) 0.047
ALL GRIDDLE 16,000 0.047” (1.19mm) 0.047
ZGP48/
ZGP36 BAKE MAIN
23,000
0.0571”
(1.35mm)
0.055
ZGP30 BAKE MAIN 21,500 0.0531” (1.35mm) 0.053
ZGP48 BAKE COMPANION 10,000 0.0374” (0.95mm) 0.037
ALL BROIL MAIN 11,500 0.041” (1.04mm) 104
ZGP48 BROIL COMPANION 9,000 0.0360” (0.91mm) 91