beautypg.com

Nilfisk-ALTO S-8 User Manual

Page 2

background image

1

SAFETY RELATED SYMBOLS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Protective Grounding

Make sure to connect the protective grounding to prevent any
electric shock before turning ON the apparatus.

Never cut off the internal or external protective grounding wire
or disconnect the wiring of protective grounding terminal.

The symbol is used to indicate that some hazard-
ous live terminals are involved within this apparatus,
even under the normal operating conditions.

The symbol is used in the service documentation

to indicate that a specific component shall be only
replaced by the component specified in that docu-
mentation for safety reasons.

Protective grounding terminal.

Alternating current /voltage.

Hazardous live terminal.

ON: Denotes the apparatus is turned on.

OFF: Denotes the apparatus is turned off, because it uses

the single pole switch, be sure to unplug the AC power to
prevent any electric shock before you proceed with your
service.

WARNING: Describes precautions that should be
observed to prevent the danger of injury or death to
the user.

CAUTION: Describes precautions that should be
observed to prevent danger of the apparatus.

WARNING

Power Supply

Ensures the source voltage matches the voltage of the
power supply before turning ON the apparatus.
Unplug this apparatus during lightning storms or when
unused for long periods of time.

External Connection
The external wiring connected to the output hazardous live
terminals requires installation by an instructed person, or the
use of ready-made leads or cords.

Do not Remove any Cover
There are maybe some areas with high voltages inside,
to reduce the risk of electric shock, do not remove any
cover if the power supply is connected.
The cover should be removed by qualified personnel
only.
No user serviceable parts inside.

Fuse
To prevent a fire, make sure to use fuses with specified stan-
dard (current, voltage, type). Do not use a different fuse or
short circuit the fuse holder.
Before replacing the fuse, turn OFF the apparatus and dis-
connect the power source.

Operating Conditions

This apparatus shall not be exposed to dripping or spl-
ashing and that no objects filled with liquids, such as
vases, shall be placed on this apparatus.
To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture.
Do not use this apparatus near water.
Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amp-

lifiers) that produce heat.
Do not block any ventilation openings.
No naked flame sources, such as lighted candles, should
be placed on the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Heed all warnings.

Follow all instructions.

Keep these instructions.

Only use attachments/accessories specified by the manu-

facturer.

Power Cord and Plug
Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at the plug, convenience receptacles, and
the point where they exit from the apparatus.

Cleaning

When the apparatus needs a cleaning, you can blow off
dust from the apparatus with a blower or clean with a rag
etc. Don't use solvents such as benzol, alcohol, or other
fluids with very strong volatility and flammability for cleaning
the apparatus body.
Clean only with a dry cloth.

Servicing

Refer all servicing to qualified personnel. To reduce the
risk of electric shock, do not perform any servicing other
than that contained in the operating instructions unless
you are qualified to do so.
Servicing is required when the apparatus has been dam-
aged in any way, such as the power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.