Audiovox Portable CD System - Manual

WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER-
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. The lightning flash and
arrowhead within the
triangle is a warning sign
alerting you of "dangerous
voltage" inside the product. The exclamation point within
the triangle is a warning sign
alerting you of important
instructions accompanying
the product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
CLASS 1 LASER PRODUCT
Should any trouble occur, disconnect the AC power cord and refer servicing
to qualified personnel.
SAFETY PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty or
humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air
flow, by covering it with a cloth, or by placing it on a carpet.
ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not
the cord itself. Pulling the cord may damage it and create hazard.
• When you are not going to use the unit for a long period of time, disconnect
the AC power cord.
ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your local
voltage.
• When there is condensation inside the unit, the unit may not function
normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually heat
the room up and dry the unit before use.
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operations are subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesirable operations.
This product contains a low power laser device.
CLASS 1 LASER
PRODUCT
APPAREIL Á LASER DE
CLASSE 1
CAUTION
INVISIBLE LASER RADIATION WHEN
OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM
SPECIFICATION CARE & MAINTENANCE
TROUBLE SHOOTING TIPS
CLEANING CD
If the CD skips or will not play, the disc may need
cleaning. Before playing, wipe the disc from the centre
out with a cleaning cloth. After playing, store the disc in
its case.
CLEANING THE TAPE HEADS
Clean the head with a cotton bud slightly moistened with
cleaning fluid or denatured alcohol.
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by
lightly wiping with a soft cloth.
IMPORTANT NOTICE:
• Should the CD door be opened before the reading of the CD is completed, a jamming
noise may occur. This can be resolved by closing the CD door and then setting the
FUNCTION switch temporarily to TAPE.
• If an abnormal display indication or an operating problem occurs, disconnect the
AC power cord and remove the batteries. Wait at least 5 seconds, then reconnect
the AC power cord or reinstall the batteries.
USING THE CASSETTE COMPARTMENT
TAPE PLAYBACK
1. Set the FUNCTION switch to
TAPE.
2. Insert a cassette tape.
3. Press the ( ) PLAY button.
TO FAST WIND
• Press the ( ) F.FWD or
( ) REWIND button.
• Press the ( ) STOP button to
stop winding at the desired
position.
TO STOP PLAYBACK
• Press the ( ) STOP
button.
1
2
3
RECORDING
USE ONLY NORMAL ( TYPE I ) TAPE FOR RECORDING.
3. Press the ( ) RECORD button.
Recording starts immediately.
The ( ) PLAY button is depressed
automatically.
3
TO STOP RECORDING
Press the ( ) STOP button.
WHEN THE END OF THE TAPE IS
REACHED
The tape stop and the buttons are
released. To record on the other
side, turn the cassette over and
press the ( ) RECORD button
again.
TO ERASE A RECORDED TAPE
1. Set the function switch to TAPE.
2. Insert a tape with the side you want to erase facing you.
3. Press the RECORD button to start erasing.
2
1. Insert a cassette tape.
2. Prepare the source to be
recorded and play it.
Recording from a CD
( Refer to CD play )
OR
Recording from the radio
( Refer to radio operation )
1
TAPE
RADIO
Disc skips
System does not turn on
Problem Solutions
Disc in place but unit
won't play
CD
• Make sure AC power plug is secure in the outlet,
and outlet has power.
• Batteries may be dead. Install new batteries.
• Make sure FUNCTION switch is set to CD.
• Make sure disc label is facing up.
• Make sure disc is clean.
• Pause mode is activated.
• Disc may be damaged or dirty; check disc.
• Make sure the unit is on a secure spot. Vibration
or jarring can cause the disc to skip.
• Electrical interference in your home can cause
poor reception. Move the unit away from
sources of interference (especially those with
motors and transformers).
• Reposition or turn the unit for better reception.
• Tape heads are dirty; clean them.
• Tape is damaged. Try another tape.
• Tabs on edge of cassette may be missing or
broken . If you want to record on that cassette,
cover the holes with removable tape.
Poor FM reception
Poor AM(MW) reception
Distorted or noisy recording
Record button wont depress
PORTABLE CD SYSTEM
OPERATION INSTRUCTION
PRINTED IN CHINA
811-128191-110
OR
OR
GENERAL
Power consumption: 10 W
Power source: AC 120V~60 Hz (USA and Canada)
AC 230V~50 Hz (Europe)
AC 240V~50 Hz (Australia)
AC 110-120V/220-240V~50/60Hz(Others)
DC 12 V (8 x "C" size or UM-2 batteries)
Specifications subject to change without notice.