Bosch WTB86200UC User Manual
Bosch Dryers
Table of contents
Document Outline
- en-us Use and care manual
- Table of contentsen-us Use and care manual
- Important information
- Your dryer is intended for
- Importance and meaning of symbols
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- Introduction to your new dryer
- Dimensions and clearances required
- Installation Instructions
- Introduction
- Before installing the dryer
- Waste disposal
- Parts provided with your dryer
- Accessories for your appliance
- Installation - step by step
- 1. Unpack the dryer.
- 1. Fasten the dryer drain hose to the washer drain/elbow as shown in picture “A”. Secure with plastic ties supplied.
- Electrical Connections
- NOTICE:
- 1. Unplug the current power cord being used from the outlet/receptacle.
- 2. To disconnect and/or reconnect a new power cord you must remove the top cover of the appliance as shown below.
- 3. Open the connection box toward the rear of the appliance by removing the T20 torx head screw fastening the cover.
- 4. Remove the 4-wire power cord (as supplied):
- NOTICE:
- NOTICE:
- NOTICE:
- 9. Ensure the terminal ends are long enough and are formed (bent) so they will align with the terminal block fastening locations (screw holes).
- 10. Reinstall the 2 terminal block screws (Philips head) at locations L as shown below.
- 11. If the ground wire shown below from N to PE is not part of the 3-wire cord assembly you have it must be obtained/purchased separately and it must be installed.
- 12. Install the last terminal block screw (Philips) and 1 grounding screw (T20 torx) at locations N and PE.
- 13. Tighten the strain relief screw ensuring the power cord cannot be pulled out of the connection box but not so tight as cut the power cord insulation.
- 14. Reinstall the connection box cover making sure all wires are routed so they do not touch any part of the enclosure and are secure.
- 15. Reinstall the appliance top cover as previously described in “2” point above.
- 9 CAUTION
- 9 CAUTION
- Leveling the dryer
- 1. Install the dryer on a level and solid surface, preferably in a corner of a room.
- 2. If the floor is uneven (or not level) adjust the dryer feet as required to level the dryer. Do not place anything under the dryer feet to help level the dryer.
- 3. Extend the dryer feet no more than is necessary. The more the feet are extended, the more vibration the dryer will experience. Start with the dryer feet turned all the way in and adjust each foot as necessary.
- 4. Use a bubble level to check the top of the dryer to make sure it is level side to side and front to rear.
- 5. Press down on each corner of the dryer top to make sure the dryer does not “wobble“. There should be no "give" or movement. All four dryer feet should press equally against the floor. This is just as important as the dryer being level to preve...
- 1. Install the dryer on a level and solid surface, preferably in a corner of a room.
- Check heating system
- Preparing to transport the dryer - step by step
- Getting to know your appliance
- Laundry
- Program selection table
- Program settings
- Additional options
- Operating Instructions
- 9 WARNING
- Your new dryer
- 9 WARNING
- Before using the dryer for the first time
- 1. Read these operating instructions carefully.
- 2. Check that the supply voltage corresponds with the voltage specifications on the rating plate on the dryer, see top rear side of the dryer and/or rating plate label inside of the dryer door.
- 3. Remove all objects from the drum.
- 4. Check the dryer for visible damage. If damage found contact your dealer.
- 5. Wipe the inside of the drum with a damp cloth.
- 6. Check heating system. ~ Check heating system; Page 15
- 7. If the dryer does not work, switch the dryer to Off. Look in the Troubleshooting section of the operating instructions and find the fault. ~ Troubleshooting; Page 28
- 1. Read these operating instructions carefully.
- Temporary disconnection of the dryer
- Using the program selector to choose a drying cycle
- Program selection
- Selecting program settings and additional options
- Loading the laundry
- Starting the program
- Indicator of program sequence
- Childproof lock
- Selecting a different program
- Cancel program
- Program end
- Removing laundry/switching the appliance off
- Signal
- Cleaning and care
- 9 WARNING
- 9 CAUTION
- Cleaning the housing and control panel
- Cleaning the lint filter
- Cleaning the heat exchanger
- 1. If the dryer is hot, run on Air fluff/No heat program to allow the dryer to cool down.
- 2. Residual water may escape, place an absorbent cloth under the maintanance flap.
- 3. Unlock the maintanance flap and open it completely.
- 4. Turn both locking levers towards each other.
- 5. Pull out the heat exchanger cap.
- 6. Remove the heat exchanger.
- NOTICE:
- 7. Rinse the heat exchanger and the cap on all sides with a jet of water to completely remove all of the fluff.
- 8. Remove any fluff from the seals on the dryer and heat exchanger.
- 9. Allow the cap and the heat exchanger to dry fully.
- 10. First insert the heat exchanger, then the cap.
- 11. Turn back both locking levers.
- 12. Close the maintanance flap until it locks into position.
- 13. Look in the Troubleshooting table also to reset the maintenance indication. ~ Troubleshooting; Page 28
- 1. If the dryer is hot, run on Air fluff/No heat program to allow the dryer to cool down.
- Cleaning the moisture sensors
- Cleaning the lint filter area
- Maintenance of drain hose
- Troubleshooting
- STATEMENT OF LIMITED PRODUCT WARRANTY