Brother XR1300 - Manual

1 Turn the power on.
2 Press the stitch category selection key
as many times as necessary until the
utility stitch indicator is lit.
3 Press (stitch selection keys). The
number of the selected stitch is
displayed.
4 Attach the presser foot indicated
in the LCD.
1 Be sure to use the correct bobbin.
2 Press down on the spool pin lever.
Remove the spool cap.
3 Fully insert the spool of thread onto
the spool pin.
Slide the spool cap onto the spool pin.
4
1 Pass the thread under the thread
guide.
2 Pass the thread under the thread
guide cover.
3 Pull the thread to the right.
Make sure that the thread passes
under the pre-tension disk.
5 Align the notch to the projection.
Slide the bobbin to the right.
6 Wind the end of the thread.
Cut the thread.
7 Slide the sewing speed controller to
the right.
8 Turn the power on.
9 Press the foot controller or press
(start/stop button) to start.
0 Winding starts. Wait until the bobbin
seems full and begins spinning slowly.
a Take your foot off the foot controller or
press (start/stop button) to stop.
b Cut the thread.
Slide the bobbin to the left and remove
the bobbin from the shaft.
c Slide the sewing speed controller
to the left.
d Turn the power off.
e Slide the button and open the cover.
f Insert the bobbin.
Push the bobbin down.
Pull the thread firmly around the tab.
Cut the thread with the cutter.
g Replace the bobbin cover.
11.5 mm
(7/16 inch)
11,5 mm
(7/16 pulg.)
1
1
3
2
4
2 3 4
5
8
6
7
9
0 a b d
f
e
g
■
Operation keys and LCD
Teclas de operación y pantalla de LCD
■
Selecting a stitch
Selección de una puntada
1 LCD (pantalla de cristal líquido)
1 Número de la puntada seleccionada
2 Pie prensatela que se va a utilizar
3 Longitud de la puntada (mm)
4 Anchura de la puntada (mm)
2 Teclas de selección de puntada
3 Tecla de ajuste de longitud de la puntada
4 Tecla de ajuste de anchura de la puntada
5 Indicador de puntada imagen en espejo
6 Indicador de puntada con aplicaciones
7 Tecla de selección de la categoría de puntada
8 Control de velocidad manual
9 Botón de Posición de aguja
0 Botón de Costura en reversa/remate
A Botón de Inicio/parar
c
Example:
Ejemplo:
(04)
Refer to the Operation Manual for detailed instructions about sewing.
Consultar el manual de instrucciones detalladas acerca de la costura.
1 LCD (liquid crystal display)
1 Number of the selected stitch
2 Presser foot to be used
3 Stitch length (mm)
4 Stitch width (mm)
2 Stitch selection keys
3 Stitch length adjustment key
4 Stitch width adjustment key
5 Mirror image stitch indicator
6 Utility stitch indicator
7 Stitch category selection key
8 Sewing speed controller
9 Needle position button
0 Reverse/reinforcement stitch button
A Start/stop button
8
9
0
A
7 5 6
3
4
2
1
1
2
1
1 2 3
2
3
2
2
1
3
1
Thread guide
Thread guide cover Pre-tension disk
4 23 4 4
8d
560b e
_
g 79ac
9a
Preparing the bobbin thread
Preparación del hilo de la bobina
PANTONE 2425 BLACK Front