MAGURA MT Series - Manual (Page 17)

i
nstallatiOn
17
Installing brake lever
L L Before.installing.your.brake.decide.which.brake.lever.(right.or.left).you.
want.to.allocate.to.your.front.wheel.or.rear.wheel.
. ) Make.sure.that.the.size.of.your.handlebar.(brake.lever.clamp.diameter).
fits.your.brake.lever.– see.
t eChniCal s peCifiCatiOns
,.page.13.
. ) Push.the.brake.lever.onto.the.handlebar.
О О The.arrows.or.the.thick.end.of.the.clamp.point.upwards!. [ A3 ]
. ) First.tighten.the.upper.clamping.screw. ( 2 ) ,.then.the.lower.one. ( 3 ) with.a.
tightening.torque.of. max. 4 Nm (35 lbf·in).
О О The.clamping.screw.is.in.contact.at.the.top,.there.is.a.gap.at.the.
.bottom!.
[ A4 ]
L L The.brake.lever.can.be.rotated.by.hand.when.forced..It.is.advantageous.
if.the.brake.lever.can.rotate.in.the.event.of.a.fall..This.reduces.the.
danger.of.irreparable.damage.to.the.handlebar.
L L If.you.reverse.the.position.(right/left).of.your.brake.levers,.you.can.
easily.change.the.position.of.the.rotating.dial.(BAT).or.cover.without.
tools.so.they.are.still.on.top..
[ A5 ]
. ) Press.the.locking.disc. ( 4 ) ,.rotate.90°.and.remove.it.with.the.clamp.
spring. ( 5 ) .
. ) Pull.and.hold.brake.lever.lightly.
. ) Pull.out.rotating.dial.(BAT). ( 6 ) .or.cover. ( 7 ) .and.replace.from.above.
. ) Position.clamp.spring.with.locking.disc,.press.and.rotate.90°.
Installing disc brake rotor
. ) Place.disc.brake.rotor.on.the.axle.flange.
О О
The.direction.arrows.point.in.the.direction.of.forward.movement.. [ A6 ]
. ) Make.sure.that.all.retaining.screws.are.coated.with.fresh.screwlock.
(medium.strength).
. ) Screw.in.retaining.screws.2.-.3.threads.
. ) Screw.in.disc.brake.rotor.clockwise.to.the.stop.
. ) Tighten.retaining screws.crosswise.to.a.tightening.torque.of.
max. 4 N·m (35 lbf·in).. [ A6 ]
L L To.install.a.Centerlock™.hub,.the..MAGURA.Centerlock adapter.is.re-
quired.
. ) Thoroughly.degrease.the.disc.brake.rotor.using.brake.cleaner.or.spirits.
Installing brake calliper
. ) Make.sure.that.the.retaining.screws.are.always.coated.with.fresh.
screwlock.(medium.strength).before.installation.
. ) Install.wheel.with.mounted.disc.brake.rotor.–.make.sure.that.the.hub.is.
correctly.seated.between.the.dropouts.
. ) If.applicable,.pull.the.transport.device.out.of.the.brake.calliper.. [ D1 ]
. ) Carefully.press.brake.pads.apart.to.the.stop.with.transport.device.or.a.
wide.screwdriver.
. ) Make.sure.that.the.brake.hose.is.optimally.positioned.– see. Aligning &
laying out the brake hose ,.page.18.
. ) Carefully.guide.the.brake.calliper.over.the.disc.brake.rotor.and.place.on.
PM.socket.or.QM-adapter..
[ A7 ]
. ) Screw.in.retaining.screws. ( 8 ) .
. ) MAgurA QM40 :.carefully.guide.brake.calliper.over.disc.brake.rotor.
and.place.on.PM.socket.with.QM40..
[ A2 ]
. ) Make.sure.that.the.convex ( 9 ) .and.concave.discs. ( 10 ) .are.correctly.posi-
tioned.
. ) Screw.in.retaining.screws.top.(M6×35). ( 11 ) .and.bottom.(M6Ч33). ( 12 ) .
О О The.brake.calliper.can.still.be.moved.slightly.but.only.wobbles.slightly.
. ) Pull.and.release.the.brake.lever.several.times.
О О
Pressure.point.is.clearly.noticeable.and.does.not.change.
. ) Pull.and.hold.brake.lever.
. ) Tighten.retaining.screws.alternately.and.in.stages.to.a.tightening.torque.
of.
max. 6 N·m (53 lbf·in).. [ A7 ] . [ A2 ]
. ) Check.that.the.disc.brake.rotor.runs.freely.–.if.necessary,.loosen.the.
retaining.screws.and.repeat.the.last.steps.