Wellsaw 1348 - Manual (Page 33)

31
Electrical Controls Electrical Controls
1 100612-004 Connector, TB-2534
2 100796-019 Hub Connector, TB-370
3 100240-001 Conduit Lock Nut
4 100612-002 Connector, TB-2523
5 100870 Electrical Enclosure
6 100869-005 Transformer, 230/460 Volts
100869-007 Transformer, 208 Volts
100869-006 Transformer, 575 Volts
7 100000-017 Machine Screw, RH 10-32 x 1/4
8 100628-017 Fuse, FNA 2-1/2 Amp
9 155115 Fuse Block Ass'y
(used w/ 115/60/1 only)
10 100796-010 Ground Screw, 10-32 x 3/8
11 * 100867 Magnetic Starter 3ph EARLIER saws
100867-018 Magnetic Starter 1ph EARLIER saws
* SEE NOTE for later sarters
12 100888-B32 Heater, B32 115/60/1 (1 req'd)
100888-B14 Heater, B14 230/60/1 (1 req'd)
100888-B128 Heater, B12.8 208/60/3 (3 req'd)
100888-B128 Heater, B12.8 230/60/3 (3 req'd)
100888-B625 Heater, B6.25 460/60/3 (3 req'd)
100888-B300 Heater, B3.00 575/60/3 (3 req'd)
13 098048-050 Gasket, SC 41, 1/8 x 3/4 x 50"
14 100000-041 Machine Screw, RH 10-32 x 1/2
15 155118 Frame Rest Ass'y, w/ cord
(Includes items 17 thru 24)
16 155118-001 Frame Rest w/ Trip Bar,
(Includes items 17 thru 19)
17 105977 Frame Rest
18 150344 Switch Bar Weldment
19 100165-005 Shoulder Bolt, 5/16 x 3/4
20 100782-012 Limit Switch, 115v w/ screws
21 100606-001 Sealing Ring
22 100612-006 Elbow, 90 deg, TB-2268
23 100015-005 Hex Nut, 6-32 (2 req'd)
24 100026-001 Washer, Shake Proof, #6 (2 req'd)
25 150235 Switch Box
26 150271 Control Switch Ass'y
(includes items 31 thru 37, and 14)
27 150236 Switch Box Cover
28 150230 Legend Plate
**Switches and contact blocks for these saws
29 100871-003 Selector Switch, Coolant ** need to be replaced together
30 100871-001 Push Button Start ** 1118 or 1318 serial number before 3085
31 100871-013 Push Button Stop ** 1338 serial number before 1784
32 100871-004 Switch Block, Coolant & Start ** 1348 serial number before 4830
33 100871-005 Switch Block, Stop **
34 100893 Back Panel
35 100892 Enclosure Cover
*NEW STARTERS
for 1318 after s/n 4105, 1338 after s/n 1935, 1348 after 4845
11 100867-029 IEC Starter 3 ph
100867-023 IEC Starter 1 ph
Adjustable Overload for IEC Starters (check motor amps)
100867-012 4-6 amps 440-460V
100867-014 7-10 amps 208-230V 3ph
100867-027 9-13 amps 208-230V 1ph
100867-022 16-24 amps 110-120V
100717-016T4 Mounting Rail for IEC
*NOTE: Various starters were used on this saw. To
make certain you receive the correct replacement
parts, contact the WELLSAW parts department with
the information on your saw’s starter.