SANDPIPER PB 1/4 - Manual (Page 11)

pb025nmdl3sm-rev0614 Page 9
ITEM PART NO. DESCRIPTION QTY
1 095-077-551 Body, Main Air Valve 1
095-077-503 Body, Main Air Valve 1
2 031-106-000 Sleeve & Spool Set 1
3 560-101-360 O-Rings 8
6 165-074-551 Cap, End with O-Ring 2
165-074-503 Cap, End with O-Ring 2
7 675-051-115 Ring, Retaining 2
8 360-085-360 Gasket, Valve Body 1
360-085-379 Gasket, Valve Body (Conductive Acetal Only) 1
9 165-072-551 Cap, Air Inlet 1
165-072-503 Cap, Air Inlet 1
10 901-037-115 Washer, Flat 1/4" 8
11 170-103-115 Capscrew, Hex Head 1/4-20 5" Long 4
12 360-084-360 Gasket, Intermediate Bracket 1
360-084-379 Gasket, Intermediate Bracket 1
(Conductive Acetal Only)
13 114-019-551 Intermediate, Bracket 1
114-019-503 Intermediate, Bracket 1
14 530-022-550 Muffler 1
15 165-073-551 Cap, Air Exhaust 1
165-073-503 Cap, Air Exhaust 1
16 545-003-115 Nut, Hex 1/4-20UNC 4
17 449-021-551 Insert, Gland 2
449-021-503 Insert, Gland 2
18 720-031-359 Seal, K-R 2
19 685-046-120 Rod, Diaphragm 1
20 755-038-000 Sleeve, Pilot Valve with O-rings 1
21 560-066-360 O-rings 6
22 675-047-115 Ring, Retaining - Pilot Valve Sleeve 1
23 775-038-000 Spool, Pilot Valve with O-rings 1
24 560-029-374 O-rings 6
25 612-147-150 Plate, Inner Diaphragm 2
26 286-069-354 Diaphragm 2
286-069-356 Diaphragm 2
286-070-600 Diaphragm 2
Composite Repair Parts List
ITEM PART NO. DESCRIPTION QTY
27 612-146-520 Plate, Outer Diaphragm 2
612-146-502 Plate, Outer Diaphragm 2|
612-146-552 Plate, Outer Diaphragm 2
28 200-057-115 Clamp, V-Band 2
29 100-002-115 T-Bolt 2
30 545-027-337 Nut, Hex 1/4-28UNF 2
31 196-145-520 Chamber, Outer 2
196-145-502 Chamber, Outer 2
196-145-552 Chamber, Outer 2
32 720-032-600 Seal, Check Valve 8
33 722-073-520 Seat, Check Valve 4
722-073-506 Seat, Check Valve 4
722-073-552 Seat, Check Valve 4
34 050-033-354 Ball, Check 4
050-033-356 Ball, Check 4
050-034-600 Ball, Check 4
35 312-095-520 Elbow, Suction 2
312-095-502 Elbow, Suction 2
312-095-552 Elbow, Suction 2
37 706-023-115 Screw, Machine 10-32UNF x 1" Long 32
38 544-004-115 Nut, Hex Flange 10-32UNF 16
39 312-096-520 Elbow, Discharge 2
312-096-502 Elbow, Discharge 2
312-096-552 Elbow, Discharge 2
40 720-033-600 Seal, Manifold 4
41 518-127-520 Manifold, Horizontal (Optional Discharge) ½
518-127-502 Manifold, Horizontal (Optional Discharge) ½
518-127-552 Manifold, Horizontal (Optional Discharge) ½
42 518-128-520 Manifold, Vertical 1
518-128-502 Manifold, Vertical 1
518-128-552 Manifold, Vertical 1
43 360-086-360 Gasket, Sealing 2
54 920-025-000 Grounding Cable (Conductive Acetal Units Only) 1
Item not shown:
**706-025-115 Screw, Machine 10-32UNF x .88" Long
This 8 foot long (244 centimeters) Grounding
Cable (Item 54) is shipped with the eyelet
fastened to the pump hardware.
To reduce the risk of static electrical sparking,
this pump must be grounded. Check the local
electrical code for detailed grounding instruction
and the type of equipment required.
Grounding The Pump
(for Conductive Acetal Pumps only)
** (use in place of four 706-023-115 machine screws with horizontal
manifold (item 41) on port side only when a pipe couple is installed
on external 1/2" NPT porting threads.
One eyelet end is fastened to the pump hardware.
One eyelet is installed to a true earth ground.
(Requires a 5/16 or 8mm maximum diameter bolt)
To be fully groundable, the pumps must be
ATEX Compliant. Refer to pump data sheet
for ordering.
Take action to prevent static
sparking. Fire or explosion can
result, especially when handling
flammable liquids. The pump,
piping, valves, containers or
other miscellaneous equipment
must be grounded.
WARNING WARNING
II 2GD T5