STI UB-1TF - Manual (Page 3)

1. TO CHANGE BUTTON COLOR AND ROUND MESSAGE
1. Choose button color. If same as existing, proceed to 2.
2. a. Loosen nut on back of switch, and push switch through plate far
enough to grasp button from back edge and remove button lens.
b. Push switch back into plate and tighten nut. Be careful not to over-
tighten.
3. Select color lens. Align notches on button with tabs on switch and push until it
snaps together.
1. Remove LED circuit board.
2. Remove current message by pushing in and
down on tabs 1 and 2 with a small screwdriver.
If necessary, also push in and down on tabs 3
and 4. Once message is loose, remove from the
front of the plate.
3. Select new message and snap into place.
Blank plates are included to create your own
custom message.
2. CHANGE TOP MESSAGE
(Refer to notes on pg. 2 for “EMERGENCY”
message use.
- 3 -
4.80 in.
(122mm)
3.22 in.(82mm)
6.31 in.(160mm)
.75 in.
(19mm) .77 in.
(20mm)
4.80 in.
(122mm)
3.22 in.(82mm)
6.25 in.(159mm)
.75 in.
(19mm) .77 in.
(20mm)
POWER IN
12-30 VDC/VAC
œ +
A
COLOR CODE:
RED
BLACK
GREEN
BLUE
WHITE
+12 VDC
-12 VDC
N.O.
COM
N.C.
INSERT PLUG INTO SWITCH WITH
RIBS IN THIS DIRECTION
DETAIL A
POWER I
N
12-30 VDC/
VAC œ +
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
BUTTON LAMP
MESSAGE LAMP
ON
GREEN
OFF
OFF
RED
ON
+
+
+
UB-1L LED PCB
NYLON WASHER
SELF TAPPING SCREW
1
2
3 4
SCREWDRIVER
Power In
12œ30 VDC/VAC
Safety Tech. Int·l Inc. P/N UB-11. Ver 1.0 wwyy
DIFFUSER
ALIGN TABS
TO NOTCHES
ON BUTTON
LENS
SWITCH NUT
DIFFUSER
MESSAGE LENS
BUTTON LENS
CONTACT LATCH TIME ADJUSTMENT:
CLOCKWISE - LONG
COUNTERCLOCKWISE - SHORT
RANGE: ~0.5 ~ 60 sec.
ACTIVATION RANGE ADJUSTMENT:
CLOCKWISE - CLOSE
COUNTERCLOCKWISE - FAR
RANGE: ~0.4 ~ 4 INCHES
~1 ~ 10 CM
12-24VDC Power Supply
19085 #6 - 32 x 1 in. OVAL
HEAD MACHINE SCREW
(2) PROVIDED
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED red
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED red
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED green
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED green
4.80 in.
(122mm)
3.22 in.(82mm)
6.31 in.(160mm)
.75 in.
(19mm) .77 in.
(20mm)
4.80 in.
(122mm)
3.22 in.(82mm)
6.25 in.(159mm)
.75 in.
(19mm) .77 in.
(20mm)
POWER IN
12-30 VDC/VAC
œ +
A
COLOR CODE:
RED
BLACK
GREEN
BLUE
WHITE
+12 VDC
-12 VDC
N.O.
COM
N.C.
INSERT PLUG INTO SWITCH WITH
RIBS IN THIS DIRECTION
DETAIL A
POWER I
N
12-30 VDC/
VAC œ +
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
BUTTON LAMP
MESSAGE LAMP
ON
GREEN
OFF
OFF
RED
ON
+
+
+
UB-1L LED PCB
NYLON WASHER
SELF TAPPING SCREW
1
2
3 4
SCREWDRIVER
Power In
12œ30 VDC/VAC
Safety Tech. Int·l Inc. P/N UB-11. Ver 1.0 wwyy
DIFFUSER
ALIGN TABS
TO NOTCHES
ON BUTTON
LENS
SWITCH NUT
DIFFUSER
MESSAGE LENS
BUTTON LENS
CONTACT LATCH TIME ADJUSTMENT:
CLOCKWISE - LONG
COUNTERCLOCKWISE - SHORT
RANGE: ~0.5 ~ 60 sec.
ACTIVATION RANGE ADJUSTMENT:
CLOCKWISE - CLOSE
COUNTERCLOCKWISE - FAR
RANGE: ~0.4 ~ 4 INCHES
~1 ~ 10 CM
12-24VDC Power Supply
19085 #6 - 32 x 1 in. OVAL
HEAD MACHINE SCREW
(2) PROVIDED
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED red
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED red
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED green
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED green
4.80 in.
(122mm)
3.22 in.(82mm)
6.31 in.(160mm)
.75 in.
(19mm) .77 in.
(20mm)
4.80 in.
(122mm)
3.22 in.(82mm)
6.25 in.(159mm)
.75 in.
(19mm) .77 in.
(20mm)
POWER IN
12-30 VDC/VAC
œ +
A
COLOR CODE:
RED
BLACK
GREEN
BLUE
WHITE
+12 VDC
-12 VDC
N.O.
COM
N.C.
INSERT PLUG INTO SWITCH WITH
RIBS IN THIS DIRECTION
DETAIL A
POWER I
N
12-30 VDC/
VAC œ +
NC
COM
NO
MAG LOCK
UB-1L LED PCB
UL Listed
NORMAL POSITION BUTTON ACTIVATED
MAGNETIC LOCK
BUTTON LAMP
MESSAGE LAMP
ON
GREEN
OFF
OFF
RED
ON
+
+
+
UB-1L LED PCB
NYLON WASHER
SELF TAPPING SCREW
1
2
3 4
SCREWDRIVER
Power In
12œ30 VDC/VAC
Safety Tech. Int·l Inc. P/N UB-11. Ver 1.0 wwyy
DIFFUSER
ALIGN TABS
TO NOTCHES
ON BUTTON
LENS
SWITCH NUT
DIFFUSER
MESSAGE LENS
BUTTON LENS
CONTACT LATCH TIME ADJUSTMENT:
CLOCKWISE - LONG
COUNTERCLOCKWISE - SHORT
RANGE: ~0.5 ~ 60 sec.
ACTIVATION RANGE ADJUSTMENT:
CLOCKWISE - CLOSE
COUNTERCLOCKWISE - FAR
RANGE: ~0.4 ~ 4 INCHES
~1 ~ 10 CM
12-24VDC Power Supply
19085 #6 - 32 x 1 in. OVAL
HEAD MACHINE SCREW
(2) PROVIDED
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED red
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED red
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED green
GREEN
BLUE
WHITE
BLACK
RED
N.C.
COM
+12VDC
GND
N.O.
EXIT
DEVICE
INPUT
UB-1TF LED
Message lit with button LED green