Pfister A89-AS1C - Manual (Page 2)

English: Thank you for purchasing this Price Pfister
product. All Price Pfister products are carefully engineered,
and factory tested to provide long trouble-free use under
normal conditions. This product is easy to install using
basic tools and our easy to follow illustrated instructions. If
you have any questions regarding this product, see info on
previous page.
1 BEFORE PROCEEDING
WARNING: Read all the instructions completely before
proceeding. Price Pfister recommends calling a professional
if you are uncertain about installing this product!
This product should be installed in accordance with all local
and state plumbing and building codes.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply
valves. These are usually found under the sink or near the
water meter. If you are replacing an existing faucet, remove
the old faucet from the sink and clean the sink surface
thoroughly.
3 ASSEMBLY INSTRUCTIONS
If operating pressures exceed 5 BAR (~75 PSI), the use of a
pressure reducer is recommended. Before proceeding with
the assembling, we advise to clean the hot and cold water
tubes, in order to avoid build-up of dirt that could compromise
the functioning of the valve.
4 VALVE INSTALLATION (Fig.A)
Place the valve body (1) into the wall, with the shower outlet
(2) facing the up. Then connect the hot water (3) supply to the
left inlet and the cold water (4) supply to the right inlet. The
embedded depth (2) of the wall (coating included) must be
within the tolerance set by the thickness of the plastic cover
(1). Carry out the finishing of the wall and remove the plastic
cover (5) by pulling firmly outward.
5 SHOWER ONLY OUTLET CONNECTIONS
(Fig.A)
Shower Outlet Pipe (2) to valve body (1). Connect Pipe Elbow
(6) (not included) to end of the pipe.
WARNING Iron Pipe Connections: When attaching
threaded fittings, use thread sealant or PTFE Plumber’s tape
according to manufacturer’s instructions.
6 TRIM FLANGE ATTACHMENT (Fig.B)
Position trim flange (1) with rubber gasket (2) onto the valve
body (3) and slide flush to wall finish. Secure by screwing cap
(4) onto valve body.
7 LEVER ATTACHMENT (Fig.C)
FOR LAGO SERIES: Place handle hub (1) on valve stem (4)
and secure with grub screw (2) (do not over tighten). Then
screw lever (3) on to back end of grub screw (do not over
tighten).
FOR ARIA AND ISOLA SERIES: Place lever (1) onto valve
stem (2). Then affix set screw (3).
CAUTION: Maintenance
DISASSEMBLY
1. Replacement parts may be available at the store where you
purchased your faucet.
2. When replacement parts are not available, please write or
call Price Pfister Consumer Service.
3. Always turn off water and relieve pressure before
working on your faucet.
NOTE: Trim Care
Cleaning Instructions:
For all Handles and decorative finishes, use only a soft damp
cloth to clean and shine. Use of polish, detergents, abrasive
cleaners, organic solvents or acid may cause damage. Use of
other than a soft damp cloth will nullify our warranty!
Special Trim:
Trim products which contain Porcelain or other similar
substance are not acceptable for public areas or Commercial
use. Installation of Said Trim is at Users Risk!
8 SHOWER ARM AND HEAD INSTALLATION
(Fig.D)
Install the shower arm flange (1) over the shower arm
(2). Place the flange firmly against the wall. Apply PTFE
plumber's tape to both ends of shower arm (2) according
to manufacturer's instructions. Screw the shower head (3) to
the shower arm (2), placing the washer (4) in between.
9 UNIT START UP
Turn on hot and cold water supplies, and check all connections
for leaks.
10 REPLACEMENT OF THE CARTRIDGE
(Fig.E)
(close the waterworks) If it becomes necessary to replace the
cartridge unscrew lever (1) from lever hub (2), and remove
grub screw. Unscrew the cap (3) and nut (4) take out the
cartridge (5). To assemble proceed in reverse order.
Supply Suggested Maximum Minimum
Hot Water
Temperature
65 Cº (150ºF) 80 Cº (175ºF) 15 Cº (60ºF)
Operating
Pressure
3 BAR (44PSI) 5 BAR (73PSI) 0.5 BAR (7PSI)
A
C
B
D
E
HOT
COLD